Items where Division is "Faculty of Mechanical Engineering" and Year is 2017

Article

Boppana V. Chowdary and Anton Gittens (2017) Effect of tool path and feed rate on the machining of coons surfaces / Boppana V. Chowdary and Anton Gittens. (2017) Journal of Mechanical Engineering (JMechE), 6 (1). pp. 1-17. ISSN 1823-5514 ; 2550-164X

A. Rahman, N. and Abdullah, M.F. and Abdullah, S. and Zamri, W.F.H. and Omar, M.Z. and Sajuri, Z. (2017) Characterising Ballistic Limits of Lightweight Laminated-Structure as a Protective Panel for Armoured Vehicle / N.A. Rahman...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (3). pp. 20-34. ISSN 18235514

A. Raus, A. and Wahab, M.S. and Ibrahim, M. and Kamarudin, K. and Ahmed, A. and Sa’ude, N. (2017) A Comparative Study of Mould Base Tool Materials in Plastic Injection Moulding to Improve Cycle Time and Warpage Using Statistical Method / A.A. Raus ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (1). pp. 1-17. ISSN 18235514 (Submitted)

A. Samat, Syafirah and Mat Isa, A.A. and Anuar, M. Azhan (2017) Performance Evaluation of Dynamic Absorbers Based on Randy Fox and Dunkerley Methods / Syafirah A. Samat ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (4). pp. 263-279. ISSN 18235514

A.K., Shafura and M.H., Mamat and M, Uzer and M., Rusop and N.D., Md Sin and A., Shuhaimi and A.H. Alrokayan, Salman and A. Khan, Haseeb (2017) Sensing properties of nanostructured zinc oxide-based gas sensor fabricated using immersion method / A.K. Shafura...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 1 (1). pp. 53-64. ISSN 1823-5514 ; 2550-164X

A.M.S., Zuan and S., Syahrullail and M.D., Arif and S., Kamitani (2017) Tribological performance of palm kernel oil at various load using pin-on-disk tribotester / A.M.S. Zuan... [et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 1 (1). pp. 91-102. ISSN 1823-5514 ; 2550-164X

A.M.S., Zuan and S., Syahrullail and N., Ngadi and Ruslan, N.N. (2017) Bio-based Lubricants from Modification of RBD Palm Kernel Oil by Trans-Esterification / A.M.S. Zuan...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (2). pp. 199-211. ISSN 18235514

Ab Wahab, Norrul Hafizan and Saad, Nor Hayati and Nasir, Norazne and Mahamad Sahab, Abdul Rahim (2017) Plaster Mould Selection for Ceramic Slip Rotary Moulding System (CSRM) / Norrul Hafizan Ab Wahab ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (5). pp. 109-120. ISSN 18235514

Abd Latif, Mohamad Zulfazli Arief and Ahmad, Muhammad Aiman and Mohd Nasir, Rizal Effendy (2017) K-180 G Micro Gas Turbine Performance Evaluation / Mohamad Zulfazli Arief Abd Latif...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (3). pp. 64-77. ISSN 18235514

Abd Manap, Muhammad Faris and Shuib, Solehuddin and Romli, Ahmad Zafir and Ahmed Shokri, Amran (2017) Finite element study of acetabular cup contact region for Total Hip Replacement (THR) / Muhammad Faris Abd Manap ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 2 (1). pp. 71-82. ISSN 1823-5514 ; 2550-164X

Abd Rahman, Khairil Muhaimin and Wirachman, Wisnoe and Istihat, Yusman (2017) The effect of orifice diameter to the acoustic signal at the hot tube of a Ranque-Hilsch Vortex Tube / Khairil Muhaimin Abd Rahman...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 2 (1). pp. 29-38. ISSN 1823-5514 ; 2550-164X

Abd Samad, Md Fahmi and Mohd Nasir, Abdul Rahman (2017) Parameter Magnitude-Based Information Criterion in Identification of Discrete-Time Dynamic System / Md Fahmi Abd Samad and Abdul Rahman Mohd Nasir. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (1). pp. 119-128. ISSN 18235514

Abdul Rahim, P.S and Shamsudin, M.S. and M., Rizamarhaiza and Nazaruddin, N.A. (2017) The effect of Nickel Oxide (NiO) compositions in consolidation of Silica-Nickel Oxide (SiO²-NiO) foams using replication method / P.S. Abdul Rahim ... [et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (5). pp. 63-72. ISSN 18235514

Abdul Saad, Wan Aliff and Mat Dzahir, Mohd Azuwan and Mohamed, Hussein and Ahmad,, Zair Asrar and Mohamad, Maziah and Mad Saad, Shaharil and Mat Dzahir, Mohd Azwarie (2017) Posture Detection on Active and Inactive Vertebrae of Spine Biomechanics in Critical Daily Activities / Wan Aliff Abdul Saad...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (2). pp. 49-74. ISSN 18235514

Abdul Sani,, Amiril Sahab and Abd Rahim, Erween and Talib, Norfazillah and Kamdani, Kamaruddin and Rahim, Mohammad Zulafif (2017) Performance Evaluation of Palm-Olein TMP Ester Containing Hexagonal Boron Nitride and an Oil Miscible Ionic Liquid as Bio-Based Metalworking Fluids / Amiril Sahab Abdul Sani ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (1). pp. 223-234. ISSN 18235514

Abdullah, Haslina and Ramli, Rizauddin and Abd Wahab, Dzuraidah and Abu Qudeiri, Jaber (2017) Comparative Study of Non-Productive Tool Path Length for Contour Parallel Machining / Haslina Abdullah...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 3 (2). pp. 211-220. ISSN 18235514

Abdullah, Mohd Azman and Ibrahim, Munaliza and Abdul Rahim, Muhammad Aliff Haika (2017) Experimental and analysis of vehicle dynamics performance based on driving behavior / Mohd Azman Abdullah... [et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 1 (1). pp. 193-206. ISSN 1823-5514 ; 2550-164X

Abdullah Make, Muhammad Razif and Faisae Rashid, Mohd Fadzil and Razali, Muhamad Magffierah and Perumal, Manugari (2017) Assembly Line Balancing using Heuristic Approaches in Manufacturing Industry / Muhammad Razif Abdullah Make...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (2). pp. 171-185. ISSN 18235514

Abdullah Ramdzam, Nazarrudin and Mahmud, Jamaluddin (2017) Investigating The Shear Behaviour of Hard Points on Honeycomb Sandwich Panels / Nazarrudin Abdullah Ramdzam and Jamaluddin Mahmud. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (4). pp. 197-210. ISSN 18235514

Abidin, Azrriq Zainul and Wan Abdul Rahaman, Wan Emri and HP Manurung, Yupiter and Abu Bakar, Muhammad Raimiey (2017) Fatigue Life Assessment of 9mm Thickness Low Carbon Steel with Multi-Objective Optimized Welding Process / Azrriq Zainul Abidin...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (1). pp. 143-153. ISSN 18235514

Adull Manan, Nor Fazli and Nik Mohd Masdek, Nik Rozlin and Abdul Aziz, Qayyum and Salleh, Zuraidah (2017) The Study of Corrosion Behaviour of Cobalt-Iron (CoFe) Alloy Coating / Nor Fazli Adull Manan ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (4). pp. 167-183. ISSN 18235514

Ahmad, Ahsana Aqilah and Rashid, Amirul Abd and Wong, Freddawati Rashiddy and Iqbal, Muhammad (2017) Worker Safety Improvement at Paper Pleating Production Line Using Poka-Yoke Concept - A Case Study in Automotive Industry / Ahsana Aqilah Ahmad ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (5). pp. 183-196. ISSN 18235514

Ahmad, Rozie Nani and Muhamad, Norhamidi and Sulong, Abu Bakar and Wahi, Azizah and Mohd Salleh, Farrahshaida (2017) Rheological properties of titanium niobium based feedstocks for metal injection moulding / Rozie Nani Ahmad...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 2 (1). pp. 139-149. ISSN 1823-5514 ; 2550-164X

Ahmad, Rozie Nani and Muhamad, Norhamidi and Wahi, Azizah and Junaidi, Syarif (2017) Parameter Optimization of Sintering Ti-6Al-7Nb Powder and Palm Stearin Binder System for the Highest Sintered Density using the Taguchi Method / Rozie Nani Ahmad...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 3 (1). pp. 55-64. ISSN 1823-5514 ; 2550-164X

Ahmad, Said and Abd Rahim, Erween and Lajis, Mohd Amri and Ibrahim, Mohd Rasidi (2017) Powder Mixed Dielectric in Electrical Discharge Machining of Inconel 718 / Said Ahmad...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (3). pp. 110-127. ISSN 18235514

Ahmad Hamidi, Mohd Faizul Farhan and Wan Harun, Wan Sharuzi and Che Ghani, Saiful Anwar and Osada, Toshiya (2017) Effect of Sintering Parameters on Physical Properties of SS 316L Alloy Compact / Mohd Faizul Farhan Ahmad Hamidi..[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 3 (2). pp. 123-131. ISSN 18235514

Ahmad Kamal, Norashikin and Sangmin, Shin and Heekyung, Park (2017) Predictive Model of Parameters Validation for the Vortexanda Technique by using Fuzzy Logic and Neural Network / Norashikin Ahmad Kamal ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (1). pp. 19-36. ISSN 18235514

Ahmed Azhar, Najwa Ezira and Shariffudin, Shafinaz Sobihana and Rusop, Mohamad (2017) Investigation of ZnO Nanotetrapods at different evaporation temperatures by thermal-CVD method for OLED applications / Najwa Ezira Ahmed Azhar...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 1 (1). pp. 19-29. ISSN 1823-5514 ; 2550-164X

Aishah Majid, Siti Najatul and Alkahari, Mohd Rizal and Ramli, Faiz Redza and Maidin, Shajahan and Tan, Chee Fai and Sudin, Mohd Nizam (2017) Influence of Integrated Pressing during Fused Filament Fabrication on Tensile Strength and Porosity / Siti Najatul Aishah Majid...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 3 (2). pp. 185-197. ISSN 18235514

Alexey A., Fedorov and Alexander V., Linovsky and Anatoliy P., Morgunov (2017) The influence of steel 35 wire EDM parameters on the surface roughness and morphology / Alexey A. Fedorov, Alexander V. Linovsky and Anatoliy P. Morgunov. (2017) Journal of Mechanical Engineering (JMechE), 14 (2). pp. 36-48. ISSN 1823-5514 ; 2550-164X

Amari, Mohamad Dzulhelmy and Che Abdullah, Sukarnur (2017) A Model for Hypersensitive Airflow Sensor Concept / Mohamad Dzulhelmy Amari ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (3). pp. 163-174. ISSN 18235514

Amat, Noor Faeizah and Muchtar, Andanastuti and Ghazali, Mariyam Jameelah and Yahaya, Norziha (2017) Effect of pH of Suspension and Mechanical Treatment on Nanosized Zirconia Dispersion / Noor Faeizah Amat...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (3). pp. 10-19. ISSN 18235514

Amiruddin, Hilmi and Wan Mahmood, Wan Mohd Faizal and Abdullah, Shahrir and Abu Mansor, Mohd Radzi and Abdollah, Mohd Fadzli and Mamat, Rizalman and Alias, Azri (2017) Effect of vaned diffuser on the performance of small turbocharger / Hilmi Amiruddin...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 1 (1). pp. 227-236. ISSN 1823-5514 ; 2550-164X

Ani, Mohammad Firdaus and Kamat, Seri Rahayu and Husin, Kalthom (2017) A Study of Psychophysical Factor for Driver Fatigue Using Mathematical Model / Mohammad Firdaus Ani...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 3 (2). pp. 109-122. ISSN 18235514

Anuar*,, M. Azhan and A. Samat, Syafirah and Mat Isa, A.A. (2017) Experimental Analysis to Evaluate the Effect of Dynamic Absorber / M. Azhan Anuar...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (4). pp. 242-262. ISSN 18235514

Asri, Nur Fawwaz and Husaini, T. and Majlan, Edy Herianto and Sulong, Abu Bakar and Wan Daud, Wan Ramli (2017) Electrochemical Behaviour and Interfacial Contact Resistance of Ti-6Al-4V and SUS 316L plates with Potential Application as a Bipolar Plate in PEMFC / Nur Fawwaz Asri ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (1). pp. 155-170. ISSN 18235514

Assan, Naziratie Assrinie and Ab. Ghani, Amir Radzi and Ramly, Ramzyzan (2017) Crush Response of Stacked Square Toroidal Tubes with A Central Tube / Naziratie Assrinie Assan ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (4). pp. 1-14. ISSN 18235514

Azaman, Aizreena and Mat Isa, Nurshazni Aiman and Mat Dzahir, Mohd Azuwan and Khor, Kang Xiang (2017) Effects of Baby Carrier on Wearer’s Posture Stability / Aizreena Azaman...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (1). pp. 107-118. ISSN 18235514

Azhari, Muhamad Azwar and Md Sallehan, Muhammad Syafi and Nazri, Muhammad Naqib (2017) Oxidation Stability Comparison between Zinc Dialkyldithiophosphate and Zinc Diamyldithiocarbarmate Induced Palm Oil Bio-lubricants / Muhamad Azwar Azhari ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (2). pp. 23-29. ISSN 18235514

Azizan, Mohd Arifhakim and Ismail, Muhammad Hussain and Mohd Salleh, Noor Azlina and Natarajan, David Valliyappan (2017) Sound absorption properties at high sound frequency of open cell aluminium foam / Mohd Arifhakim Azizan...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 2 (1). pp. 161-173. ISSN 1823-5514 ; 2550-164X

Azlisham, Nor Ain Fatihah and Mahmood, Zuliani and Mohamad, Dasmawati (2017) Evaluation of Surface Roughness and Compressive Strength of Modified Glass Ionomer Cement with Coumarin Derivatives / Nor Ain Fatihah Azlisham...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (2). pp. 216-220. ISSN 18235514

Azman,, Nurul Farhanah and Samion, Syahrullail and Abd Rahim, Erween and Shunpei, Kamitani (2017) The influence of Zinc-Dialkyl-Dithiophosphate (ZDDP) additives on the tribological performance of RBD palm kernel / Nurul Farhanah Azman...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 1 (1). pp. 65-77. ISSN 1823-5514 ; 2550-164X

Baharin, Nuraida ‘Aadilia and Muhaimin Yazit, Idznie Faidhi and Bhathal Singh, Baljit Singh and Remeli, Muhammad Fairuz and Oberoi, Amandeep (2017) Construction and Operations of First Salinity Gradient Solar Pond in Malaysia / Nuraida ‘Aadilia Baharin ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (5). pp. 217-235. ISSN 18235514

Baharom, Syazwani and Ahmad, Sufizar and Taib, Hariati (2017) The Characterization of Silica-Nickel Oxide (SiO2-NiO) Foam with Different NiO Composition and Sintering Temperatures / Syazwani Baharom...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 3 (1). pp. 135-147. ISSN 18235514

Basher, Hazril Sherney and Sh. Ahmad, Sabarinah and Abdul Rahman, Abdul Rahman (2017) Simulation of vertical greenery system in reducing energy cooling loads for high rise residential building / Hazril Sherney Basher...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 2 (1). pp. 185-196. ISSN 1823-5514 ; 2550-164X

Borůvka, Martin and Běhálek, Luboš and Habr, Jiří and Lenfeld, Petr and Vácha, Jan and Ngaowthong, Chakaphan (2017) Properties of Injection Molded Nanocomposites and Blends Based on PLA, PHBV and L-CNC / Martin Borůvka...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (3). pp. 128-141. ISSN 18235514

Bruce, Ralphin Rose.J and S, Priyadharshini (2017) Initial and progressive failure analysis of a composite wing spar structure / Bruce Ralphin Rose.J and Priyadharshini.S. (2017) Journal of Mechanical Engineering (JMechE), 14 (2). pp. 167-183. ISSN 1823-5514 ; 2550-164X

C. M., Mardziah and N. R., N. Masdek and Koay, Mei Hyie and Iis, Sopyan (2017) Physicochemical Characteristics of Magnesium Hydroxyapatite (MgHA) Derived via Wet Precipitation Method / C. M. Mardziah ... [et al.]. (2017) pp. 209-216. ISSN 18235514

C.K., Ang and W.Y., Tey and P.L., Kiew and M., Fauzi (2017) An Artificial Intelligent Approach Using Fuzzy Logic for Sleep Quality Measurement / C.K. Ang...[et al.]. (2017) Special Issue Engineering for Humanity Vol 2, SI 4 (2). pp. 31-47. ISSN 18235514

C.M., Nur Syazwani and M. Nasir, Rizal E. (2017) The Effects of Tail-Tilt on the Yaw Stability of Baseline-V Blended Wing Body Aircraft / Nur Syazwani C.M and Rizal E.M. Nasir. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (4). pp. 60-73. ISSN 18235514

Che Isa, Nik Norziehana and Mohd, Yusairie and Mohd Zaki, Mohammad Hafizudden and Syed Mohamad, Sharifah Aminah (2017) Electrodeposition and characterization of copper coating on stainless steel substrate from alkaline copper solution containing Ethylenediaminetetraacetate (EDTA) / Nik Norziehana Che Isa...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 2 (1). pp. 127-138. ISSN 1823-5514 ; 2550-164X

Che Maideen, Normariah and Budin, Salina and Sahudin, Shuib and Ab. Samat, Hasnida (2017) Synthesizing the Machine’s Availability in Overall Equipment Effectiveness (OEE) / Normariah Che Maideen ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (3). pp. 89-99. ISSN 18235514

Chng, Ming Hui and Chin, Wai Meng and Tang, Sai Hong (2017) The influence of refrigerant (R32) flow maldistribution on the thermal performance of a microchannel heat exchanger without considering superheat and sub-cool / Chng Ming Hui, Chin Wai Meng and Tang Sai Hong. (2017) Journal of Mechanical Engineering (JMechE), 14 (2). pp. 149-166. ISSN 1823-5514 ; 2550-164X

Cosmas, P Pagwiwoko and Louis, Jezequel (2017) Modelling of Flutter Vibration using System Dynamic Approach for Analysing Limit Cycle Oscillations / Cosmas P Pagwiwoko and Louis Jezequel. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (5). pp. 27-41. ISSN 18235514

D., Sivakumar and L.F., Ng and Selamat, Mohd Zulkefli (2017) Investigation on fatigue life behaviour of sustainable bio-based fibre metal laminate / D. Sivakumar...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 1 (1). pp. 123-140. ISSN 1823-5514 ; 2550-164X

D., Sivakumar and L.F., Ng, and Selamat, M. Z. (2017) Failure analysis of hybrid fibre reinforced plastics for bolted joint under thermal effect / D. Sivakumar...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 1 (1). pp. 141-156. ISSN 1823-5514 ; 2550-164X

El-Mahdy, Loai A. and Ahmed, Mahmoud Y. M. and Mahmoud, Osama K. and Abdel-Hameed, Omar E. (2017) A Comparative Study of Prediction Techniques for Supersonic Missile Aerodynamic Coefficients / Loai A. El-Mahdy … [et al.]. (2017) Journal of Mechanical Engineering (JMechE), 14 (1). pp. 35-60. ISSN 1823-5514 ; 2550-164X

Elias, Husna and A., Kalam and Abd Rahman, Noorleha and Koay, Mei Hyie (2017) Transformation of wood powder carbon template into biomorphic silicon carbide / Husna Elias...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 2 (1). pp. 151-160. ISSN 1823-5514 ; 2550-164X

Fonna, Syarizal and Huzni, Syifaul and Zaim, Ahmad and Ariffin, Ahmad Kamal (2017) Simulation of Cathodic Protection on Reinforced Concrete Using BEM / Syarizal Fonna...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (2). pp. 111-112. ISSN 18235514

Hafidz Arif Razali, Mohamad Nor and Shaikh Salim, Sheikh Ahmad Zaki and Mat Ali, Mohamed Sukri and Ahmad, Nurul Huda (2017) Large-Eddy Simulation of Wind Flow within a Canyon between Modified Idealized Terraced Houses / Mohamad Nor Hafidz Arif Razali...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 2 (2). pp. 243-253. ISSN 1823-5514 ; 2550-164X

Hamat, A. Malik and Ghazali, M. Fairusham and Priyandoko, Gigih (2017) The Use of Transmission Line Modelling for Detection of Leakage in Pipeline / A. Malik Hamat...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (4). pp. 74-83. ISSN 18235514

Hamid, K.A. and Azmi, W.H. and Nabil, M.F. and Mamat, Rizalman (2017) Heat transfer augmentation of mixture ratio TiO2 to SiO2 in hybrid nanofluid / K.A. Hamid...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (3). pp. 51-63. ISSN 18235514

Hanapi, Muhammad Ikhmal and Ahmad, Sufizar and Taib, Hariati and Tan, Chee Chen (2017) Physical Properties of Porcelain Ceramic with Influence of Milled Alkali Resistant (AR) Fibreglass for Sewer Pipes Application / Muhammad Ikhmal Hanapi...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (3). pp. 1-9. ISSN 18235514

Harun, Azmi and Sia, Ting Ting and Che Haron, Che Hassan and A. Ghani, Jaharah and Mokhtar, Suhaily (2017) A Study on Parameter Optimization of the Delamination Factor (Fd) in Milling Kenaf Fiber Reinforced Plastics Composite Materials Using DOE Method / Azmi Harun...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 3 (1). pp. 211-224. ISSN 18235514

Harun, Nurul Hatiqah and Kasim, Mohd Shahir and Raja Abdullah, Raja Izamshah and Boejang, Hambali and Attan, Hassan (2017) Feasible Study on Dental Restoration Using Time Compression Technologies / Nurul Hatiqah Harun...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 3 (1). pp. 89-96. ISSN 1823-5514 ; 2550-164X

Hashim, Hafizan and Ab. Ghani, Amir Radzi and Wahyu, Kuntijoro (2017) Bending Collapse of Closed-hat-section Beams. Part II: Theoretical Model Modification and Validation / Hafizan Hashim ... [et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 2 (2). pp. 57-69. ISSN 1823-5514 ; 2550-164X

Hashim, Hafizan and Ab.Ghani, Amir Radzi and Kuntjoro, Wahyu (2017) Bending collapse of closed-hat-section beams. Part I: Development and validation of finite element models / Hafizan Hashim...[et al.]. (2017) Journal of Mechanical Engineering, SI 2 (1). pp. 57-69. ISSN 1823-5514

Hassan, Kamarul Nizam and Hussain, Ahmad Kamil and Mahmud, Jamaluddin (2017) Static Stability Determination Of An Exhaust Stack Structure Using Finite Element Analysis / Kamarul Nizam Hassan ... [et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (5). pp. 153-166. ISSN 18235514

Hassan, Sharudin and A. Ghani, Jaharah and Che Haron, Che Hasan and Md Dali, Mohd Nor Azam (2017) Development of Dynamic Assisted Tooling Using TRIZ Approach for Dimple Structure Fabrication in Milling Process / Sharudin Hassan...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 3 (1). pp. 23-32. ISSN 1823-5514 ; 2550-164X

Hassan, Sharudin and A. Ghani, Jaharah and Che Haron, Che Hassan and Mohd Dali, Mohd Nor Azam and Rizal, Muhammad (2017) A review of the milling process to fabricate a dimple structure / Sharudin Hassan...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 1 (1). pp. 175-192. ISSN 1823-5514 ; 2550-164X

Hassan, Siti Fatimah and Wan Zamri, Wan Fathul Hakim and Mohamed, Intan Fadhlina and Wan Ghopa, Wan Aizon and Md Din, Mohamad Faiz (2017) Influence of Bi Layer Structure and Sub Layer Distance on the Hardness of Multilayer Thin Film TiAlN and CrN / Siti Fatimah Hassan...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 3 (1). pp. 199-210. ISSN Special Issue Manufacturing Sustainability towards a Greener Future Vol 1

Hosnie, Siti Mariana and Ismail, Muhammad Hussain and Yahaya, Mazyan and Haris, Nurul ‘Ain and Iain, Todd (2017) Fabrication of Porous β-Type Ti-40Nb Alloys Incorporated with TiH2 via Powder Metallurgy Processing Route Under Reducing Environment / Siti Mariana Hosnie...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 2 (2). pp. 99-112. ISSN Special Issue 2017 Vol 2: Frontiers in Sustainable Energy Research for Humanity

Ibrahim, Dzullijah and Yaakob, Yusli and Hussin, Norasikin and Samad, Zahurin (2017) STEP-NC Interpolator for General 2D and 3D Parametric Curve / Dzullijah Ibrahim...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (2). pp. 269-277. ISSN 18235514

Ilias, Mohd Rijal and Rawi, Noraihan Afiqah and Shafie, Sharidan (2017) Steady Aligned MHD free convection of ferrofluids flow over an inclined plate / Mohd Rijal Ilias, Noraihan Afiqah Rawi and Sharidan Shafie. (2017) Journal of Mechanical Engineering (JMechE), 14 (2). pp. 1-15. ISSN 1823-5514 ; 2550-164X

Ismail, Muhammad Zaiyad and Azizan, Nur Akmal and Ja’afar, Rabi’atul’adawiyah and Ayub, Muhammad Azmi and Khalid, Noor Khafifah (2017) DC Motor Friction Identification With ANFIS and LS-SVM Method / Muhammad Zaiyad Ismail ... [et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (5). pp. 98-108. ISSN 18235514 (Unpublished)

Ismail, Nur Farhani and Muhamad, Norhamidi and Sulong, Abu Bakar and Che Haron, Che Hassan and Tholibon, Dulina and Tharazi, Izdihar and MdRadzi, Mohd Khairul Fadzly and Razak, Zakaria (2017) Mechanical Properties of Compression Molded Epoxy Polymer Composites Reinforced with Kenaf Fibers / Nur Farhani Ismail ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 3 (2). pp. 1-12. ISSN 18235514

Jamaludin, Siti Nabihah and Mohd Salleh, Ruzitah (2017) Equilibrium Solubility of Carbon Dioxide in Aqueous 2-Amino-2-Methyl-1-Propanol (AMP) Blended with 2-Methylpiperidine (2MPD) at High Pressure / Siti Nabihah Jamaludin...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 2 (1). pp. 175-184. ISSN 1823-5514 ; 2550-164X

Kadarman, A Halim and Shuib, Solehuddin and Hassan, Ahmad Yusoff and Ahmad Zahrol, Muhammad Adib Izzuddin (2017) Thin-walled box beam bending distortion analytical analysis / A Halim Kadarman … [et al.]. (2017) Journal of Mechanical Engineering (JMechE), 14 (1). pp. 1-17. ISSN 1823-5514 ; 2550-164X

Kamarudin, K. and Wahab, M.S. and Ibrahim, M. and M. Batcha, M.F. and A. Raus, A. and Ahmed, Aqeel and Sa’ude, N. (2017) The Effect of Square Finned Conformal Cooling (SFCC) on Cycle Time for Plastic Injection Moulding / K. Kamarudin ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (1). pp. 79-92. ISSN 18235514

Kamarul Bahrain, Siti Humairah and Mahmud, Jamaluddin and A. Rasid, Zainudin and Madete, June (2017) Synthesization and Microstructural Analysis of Arenga Pinnata Fibres and Silicone Rubber for New Silicone Biocomposite Material / Siti Humairah Kamarul Bahrain ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (4). pp. 15-30. ISSN 18235514

Kaur, Wandeep and Balakrishnan, Vimala (2017) Social Media Sentiment Analysis of Thermal Engineering Students for Continuous Quality Improvement in Engineering Education / Wandeep Kaur ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (1). pp. 263-272. ISSN 18235514

Khairuzzaman, Noor Aishah and Hashim, Hadzli and Mohd Sampian, Ahmad Faiz and Yussuf, Ummu Raihan (2017) White Root Disease Infected Rubber Tree Detection Through Statistical Inference of Dry Rubber Sheet Near Infrared (NIR) Spectrum Measurement Method / Noor Aishah Khairuzzaman...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 2 (2). pp. 167-177. ISSN 1823-5514 ; 2550-164X

Khamis, Nor Kamaliana and Md Deros, Baba and Nawawi, Roslizawati and Saleh, Chairul (2017) Muscle Activity of the Upper and Lower Body Part in Car Gearing Action: A Preliminary Study / Nor Kamaliana Khamis...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 3 (2). pp. 157-165. ISSN 18235514

Lim, Chong Lye and Adam, Nor Mariah and Ahmad, Kamarul Arifin and Ahmedov, Anvarjon (2017) Cryogenic Pipe Flow Simulation for Liquid Nitrogen / Lim Chong Lye...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 2 (2). pp. 179-198. ISSN 1823-5514 ; 2550-164X

Lim, Chong Lye and Adam, Nor Mariah and Ahmad, Kamarul Arifin and Ahmedov, Anvarjon (2017) Derivation of three-dimensional heat transfer mathematical equations to predict conductivity of insulation systems for liquid nitrogen pipe flow / Lim Chong Lye...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 2 (1). pp. 39-56. ISSN 1823-5514 ; 2550-164X

Lip, Kean Moey and Adam, Nor Mariah and Ahmad, Kamarul Arifin (2017) Effect of Venturi-Shaped Roof Angle on Air Change Rate of a Stairwell in Tropical Climate / Lip Kean Moey ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (4). pp. 135-150. ISSN 18235514

Lippong, Tan and Date, Abhijit and Houshyar, Shadi and Singh, Baljit and Lai, Chet Ding and Bingjie, Zhang (2017) A Comparative Study of Firefighters’ Clothing using Organic and Inorganic Phase Change Material / Lippong Tan ... [et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (5). pp. 84-97. ISSN 18235514

M., Amiri (2017) An experimental and theoretical analysis of projectile and target geometry effects on ballistic limit velocity / M. Amiri. (2017) Journal of Mechanical Engineering (JMechE), 14 (1). pp. 19-33. ISSN 1823-5514 ; 2550-164X

M. F., M. Sharif and A., A. Saad and F. C., An and M. Y., T. Ali and Z., Samsudin (2017) Effect of Stretchable Circuit Deformation on Its Electrical Performance for Automotive Lighting Application / M. F. M. Sharif...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (2). pp. 279-287. ISSN 18235514

M. Jamil, W. N. and Sajuri, Z. and Aripin, M. A. and Abdullah, S. and Omar, M. Z. and Abdullah, M.F. and H. Zamri, W. F. (2017) Effect of Steel Fibres And Wire Mesh Reinforcement on Flexural Strength and Strain Energy Steel-Epoxy-Aluminium Composite Laminates / W. N. M. Jamil ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (1). pp. 185-196. ISSN 18235514

M. N., Muhamed and M. Z., Omar and S., Abdullah and Z., Sajuri and W. F. H., W. Zamri (2017) The Effect of Surface Texture on the Joint Shear Strength of AR500 Steel and AA7075 / M. N. Muhamed...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (2). pp. 289-301. ISSN 18235514

M. Nasir, Rizal E. and Basri, Ilyas H. and M. Ahmad, Aiman and A. Latif, Zulfazli A. and Wisnoe, Wirachman and Kuntjoro, Wahyu (2017) The Effect of Elevons Deflection to Aerodynamic Coefficients of A Tail-less Blended Wing-Body Planform / Rizal E. M. Nasir ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (4). pp. 151-166. ISSN 18235514

M. S., M. Zaharin and N. R., Abdullah and Dahalan, M. Imran and Sharudin, Hazim and A.R., Asiah and M., Beriache (2017) Experimental Study on the Effects of Methanol and Ethanol on Gasoline Engine Performance and Exhaust Emissions / M. S. M. Zaharin...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 2 (2). pp. 27-44. ISSN 1823-5514 ; 2550-164X

M.A., Mahamood and N., Mohamad and A.R., Jeeffeerie and A.H., Mohd Zain (2017) Correlation of open cell structure with properties of green rubber foam from epoxidised natural rubber/reclaimed rubber glove / M.A. Mahamood...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 1 (1). pp. 113-122. ISSN 1823-5514 ; 2550-164X

M.A. Al-quraan, Tareq (2017) A manifestation of non-hydrodynamic factors in steady-state conditions of friction / Tareq M.A. Al-quraan. (2017) Journal of Mechanical Engineering (JMechE), 14 (2). pp. 109-124. ISSN 1823-5514 ; 2550-164X

M.Yusop, Hanafi and Ghazali, M.F. and M.Yusof, M.F. and W.Hamat, W.S. (2017) Development of Intelligent Leak Detection System Based on Artificial Pressure Transient Signal Using Integrated Kurtosis-Based Algorithm for Z-Filter Technique (I-Kaz) / Hanafi.M.Yusop...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (4). pp. 84-102. ISSN 18235514

M.Z., Sharif and W.H., Azmi and A.A.M, Redhwan and N. N, M. Zawawi (2017) Improvement of Nanofluid stability using 4-Step UV-Vis Spectral Absorbency Analysis / M.Z. Sharif...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (2). pp. 233-247. ISSN 18235514

MD Alias, Muhammad Aizat and Azhari, Muhamad Azwar (2017) Preliminary Feasibility Studies of Vegetable Oil as Substitution to Mineral Lubricant / Muhammad Aizat MD Alias and Muhamad Azwar Azhari. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (1). pp. 37-46. ISSN 18235514

Mahaidin, Ahmad Aswad and Jaafar, Talib Ria and Budin, Salina and Selamat, Mohd Asri (2017) The Effect of Cobalt, Vanadium Carbide and PKS Activated Carbon Addition on WC-Co Composite: A Study using Taguchi Method / Ahmad Aswad Mahaidin ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (5). pp. 42-52. ISSN 18235514

Mahmud, Khan Raqib and M. M., Rhaman and Al Azad, Abul Kalam (2017) Parametric studies and reliability of near-wall turbulence modeling for Large Eddy Simulation of incompressible flows / Khan Raqib Mahmud, M. M. Rhaman and Abul Kalam Al Azad. (2017) Journal of Mechanical Engineering (JMechE), 14 (2). pp. 125-147. ISSN 1823-5514 ; 2550-164X

Mahmud, Nor Laili and Mohd Arshad, Mohd Arshad and Adnan, Ramli (2017) Sliding Mode Controller Design Based on Pole Placement Method / Nor Laili Mahmud...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 2 (2). pp. 135-144. ISSN 1823-5514 ; 2550-164X

Mali, Mohamad and Samsudin, Azizul Hakim and Mahmud, Jamaluddin and Hussain, Ahmad Kamil (2017) Failure Analysis of Composite Laminates Under Biaxial Tensile Load Due To Variations in Lamination Scheme / Mohamad Mali ... [et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (5). pp. 167-182. ISSN 18235514

Masri, Nurhidayah and Md Deros, Baba and Mohd Yusof, Hanizah (2017) Work-Related Musculoskeletal Disorders Among Tea Pluckers / Nurhidayah Masri...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 3 (2). pp. 221-232. ISSN 18235514

Mat Asim, Mohd Tarmizi and Tengku Ibrahim, Tengku Muhammad Fahmi and Adam, Nor Mariah (2017) Strategic energy management plan and MS ISO 50001:2011 compliance / Mohd Tarmizi Mat Asim...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 2 (2). pp. 1-25. ISSN 1823-5514 ; 2550-164X

Mat Dzahir, Mohd Azuwan and Mat Dzahir, Mohd Azwarie and Hussein, Mohamed and Ahmad, Zair Asrar and Mohamad, Maziah and Mad Saad, Shaharil (2017) Hysteresis Modelling of Pneumatic Artificial Muscle using General Cubic Equation and Factor Theorem Prediction Method / Mohd Azuwan Mat Dzahir...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (2). pp. 1-21. ISSN 18235514

Mazlan, Muhammad Hazli and Mitsugu, Todo and Ikuho, Yonezawa and Hiromitsu, Takano (2017) Biomechanical Alteration of Stress and Strain Distribution Associated with Vertebral Fracture / Muhammad Hazli Mazlan...[et al.]. (2017) Takano, SI 2 (2). pp. 123-133. ISSN 18235514

Md Ghazaly, Mariam and Soo, Kok Yew and Abdullah, Zulkeflee and Mohd Ali, Mohd Amran and Chong, Shin Horng and Che Amran, Aliza (2017) Trajectory tracking of a mobile robot system / Mariam Md Ghazaly...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 1 (1). pp. 207-226. ISSN 1823-5514 ; 2550-164X

Md Sah, Muhammad Hanafi and Mohd Noor, Alias and Abbas, Muhammad Rabiu and Abu Bakar, Aznizam (2017) Mechanical properties of coconut shell powder reinforced PVC composites in automotive applications / Muhammad Hanafi Md Sah … [et al.]. (2017) Journal of Mechanical Engineering (JMechE), 14 (2). pp. 49-61. ISSN 1823-5514 ; 2550-164X

Md Tahir, Nurul Hidayah and Rizal, Muhammad and Wan Mansor, Wan Nuha and A. Ghani, Jaharah and Nuawi, Mohd Zaki and Che Haron, Che Hassan (2017) The Correlation Between Tool Wear and Vibration Signals from Piezoelectric in End Milling of AISI P20+NI / Nurul Hidayah Md Tahir...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 3 (2). pp. 49-62. ISSN 18235514

Mohamad, Nor Syahirah and Kasolang, Salmiah (2017) Application of Response Surface Methodology in Characterization of Biolubricant with Titanium Oxide Nanoparticles / Nor Syahirah Mohamad and Salmiah Kasolang. (2017) Journal of Mechanical Engineering (JMechE), SI 2 (2). pp. 231-241. ISSN 1823-5514 ; 2550-164X

Mohamad Kamal, Mohamad Ridzuan and Abdul Rahman, Abdul Raheem and Wakhi Anuar, Nur Farah Bazilah and Salleh, Mohd Shukor (2017) Effect Of Coating Thickness On The Microstructure And Mechanical Properties Of AL-SI (LM6) Alloy Lost Wax Casting / Mohamad Ridzuan Mohamad Kamal...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 3 (1). pp. 97-106. ISSN 1823-5514 ; 2550-164X

Mohamad Samsuddin, Noorazizi and Izamshah, Raja and Kasim, Mohd Shahir and Che Haron, Che Hassan (2017) Evaluation of Hole Performance and Force Magnitude on Drilling Parameter for Orthopaedic Surgical Bone Drilling / Noorazizi Mohamad Samsuddin ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 3 (2). pp. 37-47. ISSN 18235514

Mohamed, Mohamed Ackiel and Manurung, Yupiter Hp (2017) Effect of friction stir welding parameters on fatigue resistance, weld quality and mechanical properties of Al 6061-T651 / Mohamed Ackiel Mohamed and Yupiter HP Manurung. (2017) Journal of Mechanical Engineering (JMechE), SI 2 (1). pp. 83-99. ISSN 1823-5514 ; 2550-164X

Mohamed Thaheer, Ahmad Shaqeer and Ismail, Norilmi Amilia (2017) Mission design and analysis of USM high-altitude balloon / Ahmad Shaqeer Mohamed Thaheer and Norilmi Amilia Ismail. (2017) Journal of Mechanical Engineering (JMechE), 14 (2). pp. 62-92. ISSN 1823-5514 ; 2550-164X

Mohamed Zukri, Mohammad Nizar and Abu Bakar, Elmi (2017) An Electroanalytical Instrument Equipped with Wireless Communication Network and Graphical User Interface for Real-time Monitoring Wastewater Status from Batik Industry / Mohammad Nizar Mohamed Zukri and Elmi Abu Bakar. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (2). pp. 153-170. ISSN 18235514

Mohammad, Rosdi and Mohd Ariffin, Mohd Kharul Anuar and Baharuddin, B. T. Hang Tuah and Mustapha, Faizal and Aoyama, Hideki (2017) The Effects of Single Cutting Tool Geometry on Surface Roughness / Rosdi Mohammad...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 3 (1). pp. 45-54. ISSN 1823-5514 ; 2550-164X

Mohammed El Sallah, Zagane and Ismail, Benbarek and Ali, Benouis and Abderahmen, Sahli and Bel Abbes, Bachir Bouiadjra and Serier, Boualem (2017) Numerical simulation of the femur fracture with and without prosthesis under static loading using extended finite element method (X-FEM) / Zagane Mohammed El Sallah … [et al.]. (2017) Journal of Mechanical Engineering (JMechE), 14 (1). pp. 109-124. ISSN 1823-5514 ; 2550-164X

Mohd Anuar, Mohd Afzan and Todo, Mitsugu (2017) Mechanics of Posterior Stabilized Total Knee Arthroplasty During Daily Activities in Relation to Prosthesis Condylar and Post-cam Design: A Finite Element Study / Mohd Afzan Mohd Anuar and Mitsugu Todo. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (4). pp. 211-228. ISSN 18235514

Mohd Dali, Mohd Nor Azam and A. Ghani, Jaharah and Che Haron, Che Hassan and Rizal, Muhammad (2017) TRIZ approach for designing a new assisted tooling for dimple structure fabrication / Mohd Nor Azam Mohd Dali...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 1 (1). pp. 79-90. ISSN 1823-5514 ; 2550-164X

Mohd Hassan, Siti Lailatul and Sulaiman, Nasri and Jaafar, Haslina and Saparon, Azilah (2017) Implementation of Pipelined FFT Processor on FPGA Microchip Proposed for Mechanical Applications / Siti Lailatul Mohd Hassan...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 2 (2). pp. 145-156. ISSN 1823-5514 ; 2550-164X

Mohd Resali, Mohd Sofwan and Salleh, Hanim (2017) Development of Multiple-Input Power Management Circuit for Piezoelectric Harvester / Mohd Sofwan Mohd Resali and Hanim Salleh. (2017) Journal of Mechanical Engineering (JMechE), SI 2 (2). pp. 215-230. ISSN 1823-5514 ; 2550-164X

Mohd Resali, Mohd Sofwan and Salleh, Hanim (2017) Effect of Rubber Compound Treatment and PTFE Extension Beam on Piezoelectric Energy Harvester Power Density / Mohd Sofwan Mohd Resali and Hanim Salleh. (2017) Journal of Mechanical Engineering (JMechE), SI 2 (2). pp. 199-214. ISSN 1823-5514 ; 2550-164X

Mohd Resali, Mohd Sofwan and Salleh, Hanim (2017) Wireless Condition Monitoring System for Rotating Machinery Powered by a Hybrid Vibration Based Energy Harvester / Mohd Sofwan Mohd Resali and Hanim Salleh. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (2). pp. 249-267. ISSN 18235514

Mohd Sabri, Norlina and Puteh, Mazidah and Md Sin, Nor Diyana (2017) Artificial intelligence technique in solving nano-process parameter optimization problem / Norlina Mohd Sabri...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 1 (1). pp. 1-17. ISSN 1823-5514 ; 2550-164X

Mohd Salleh, Farrahshaida and Sulong1, Abu Bakar and Foudzi1, Farhana and Mohamed1, Intan Fadhlina and Azaman1, Natasha Emira and Mas’ood1, Najlaa Nazihah and Seong, Jin Park (2017) Flow Behaviour Characterization of Hydroxyapatite for Powder Injection Moulding (PIM) / Farrahshaida Mohd Salleh...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 3 (1). pp. 77-88. ISSN 1823-5514 ; 2550-164X

Mohd Salleh, Norshariza and Ahmad Shauri, Ruhizan Liza and Nasir, Khairunnisa and Remeli, Nurul Hanani (2017) Fuzzy-PID Position Control of a Three Fingered Robot Hand for Grasping Varying Loads / Norshariza Mohd Salleh ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (1). pp. 61-77. ISSN 18235514

Mohd Zin, Mohd Syazwan and Abdul Rani, Muhamad Norhisham and Yunus, Mohd Azmi and Wan Iskandar Mirza, Wan Imaan Izhan and Mat Isa, Ahmad Azlan and Mohamed, Zulkifli (2017) Modal And FRF Based Updating Methods For The Investigation Of The Dynamic Behaviour Of A Plate / Mohd Syazwan Mohd Zin ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (3). pp. 175-189. ISSN 18235514

Mokhtar, Suhaily and Che Haron, Che Hassan and A. Ghani, Jaharah and Harun, Azmi (2017) Evaluation of Thrust Force in Drilling of Woven Kenaf Fiber Reinforced Epoxy Composite Laminates / Suhaily Mokhtar...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 3 (1). pp. 148-168. ISSN 18235514

Muhalim, Nur Amanina Damira and Md Daud, Mohd Yusof and Hassan, Mohamad Zaki and Abdul Aziz, Sa’ardin and Abdul Raman, Norazmein and Sarip, Shamsul (2017) Compressive Behaviour and Energy Absorption of Copper Tube under Quasi Static and Ultrasonic Compression Test / Nur Amanina Damira Muhalim...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 3 (1). pp. 169-184. ISSN 18235514

Mustapa, Mohd Sabri and Shaikh Salim, Sheikh Ahmad Zaki and Mat Ali, Mohamed Sukri and Rijal, Hom Bahadur (2017) Investigation of Thermal Comfort at Different Temperature Settings for Cooling in University Building / Mohd Sabri Mustapa ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (4). pp. 123-134. ISSN 18235514

N. F. A., Shafie and A. I. S., Rahman and A., Yahya and U. Q. A., Mansor and A. M., Som and A. H., Nour and Z., Hassan and R. M, Yunus (2017) Performance of Ultrasonic-assisted Membrane Anaerobic System (UMAS) on Palm Oil Mill Effluent (POME) / Shafie N. F. A....[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 2 (1). pp. 17-27. ISSN 1823-5514 ; 2550-164X

N. I., Ismail and A. H., Zulkifli and H., Yusoff and R. J., Talib and A.R., Hemdi and N. Mustapa, N. M. Muzammil (2017) Aerodynamic Performances of MAV Wing Shapes / N. I. Ismail...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (2). pp. 187-198. ISSN 18235514

Narong Oh, Lai Ching and Sia, Chee Kiong and Zainudin, Azlan and Yee, See Khee (2017) Exploring the Potential of Palm Oil Fuel Ash (POFA) in EMI Shielding Effectiveness / Narong Oh Lai Ching...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 2 (1). pp. 101-111. ISSN 1823-5514 ; 2550-164X

Nasir, Norazne and Saad, Nor Hayati and Sahruddin, Fatin Syafinaz and Ab Wahab, Norrul Hafizan (2017) Fine Bone China Product using Ceramics Slip Rotary Moulding (CSRM) Technique / Norazne Nasir ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (4). pp. 31-42. ISSN 18235514

Nasir, R. M. and B.T., Ting, and Saad, A. Y. and S., Mridha (2017) Dry/wet sliding activation wear of pure Al / R. M. Nasir...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 1 (1). pp. 157-174. ISSN 1823-5514 ; 2550-164X

Nazaruddin, N.A. and Abdul Rahim, P.S. and M., Rizamarhaiza and A. A. K, W.M. Hasif. and Azmi, M.Azham and Taib, H. and Ahmad, S. (2017) The Effect of Different Binder Compositions in Fabricating Silica Foam (SiO2) Via Replication Method / N.A.Nazaruddin...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (5). pp. 53-62. ISSN 18235514

Negin, O. Aminian and I. Romli, Fairuz (2017) Study on the Potential of Airships as Urban Mass Public Transport in Malaysia / Negin O. Aminian and Fairuz I. Romli. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (2). pp. 221-232. ISSN 18235514

Niti, Kammuang-lue and Kritsada, On-ai and Phrut, Sakulchangsatjatai and Pradit, Terdtoon (2017) Thermal Characteristics of a Rotating Closed-Loop Pulsating Heat Pipe Affected by Centrifugal Accelerations and Numbers of Turns / Niti Kammuang-lue ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (3). pp. 35-50. ISSN 18235514

Nurzaki, I. and Abdullah, A. Saifizul and Ramli, R. (2017) Experimental Validation of Vehicle Dynamic Characteristics of a Virtual Heavy Vehicle Model / I. Nurzaki ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (5). pp. 131-143. ISSN 18235514

Omar, Rohaizat and Abdul Rani, Muhamad Norhisham and Wan Iskandar Mirza, Wan Imaan Izhan and Yunus, Mohd Azmi and Othman, Mohd Hakimi (2017) Finite Element Modelling and Updating for Bolted Lap Joints / Rohaizat Omar...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (3). pp. 202-222. ISSN 18235514

Pangesty, Azizah and Todo, Mitsugu (2017) Preparation and Characterization of porous tubular scaffold made of PCL/PLCL blends for vascular tissue engineering / Azizah Pangesty and Mitsugu Todo. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (4). pp. 184-196. ISSN 18235514

Peck, Loo Kiew and Kian, Hen Chong (2017) Development of Fruit-Based Waste Material as Bioflocculant for Water Clarification / Peck Loo Kiew and Kian Hen Chong. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (5). pp. 1-10. ISSN 18235514

Rabilah, Rosniza and Budin, Salina and Jaafar, Talib Ria and Hashim, Siti Mardini (2017) Influence of Waste Plastic Binder on Sintered Properties of Injection Moulded M2 HSS / Rosniza Rabilah...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (1). pp. 197-206. ISSN 18235514

Rajendran Royan, Nishata Royan and Sulong, Abu Bakar and Mohd, Nor Yuliana Yuhana and Abdul Ghani, Mohd Hafizuddin and Ahmad, Sahrim (2017) Effect UV/O3 Modified Rice Husk on the Mechanical Properties of Recycle HDPE Rice Husk Composite / Nishata Royan Rajendran Royan ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 3 (2). pp. 13-22. ISSN 18235514

Ram, Nathi and C. Sharma, Satish and K. Rajput, Arvind (2017) Compensated hole-entry Hybrid Journal Bearing by CFV Restrictor under Micropolar Lubricants / Nathi Ram...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 1 (1). pp. 31-42. ISSN 1823-5514 ; 2550-164X

Ramli, Azlan and Raja Abdullah, Raja Izamshah and Abu Bakar, Mohd Hadzley and Kasim, Mohd Shahir and A. Rahman, Muhamad Arfauz and Mohd Zakaria, Muhammad Akmal (2017) Investigation on Improvement of Surface Roughness Using Rotary Ultrasonic Assisted Machining Technique for Hardened Steel Material / Azlan Ramli...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 3 (1). pp. 118-134. ISSN 18235514

Ramli, Mohd Badli and Wahab, M.S. and Zain, B.A and Raus, A.A. and Kamarudin, K. and Sa`ude, N and Haq, R and M, Ibrahim and Ahmed, Aqeel (2017) Effect Of Incubation Temperature On Ikta’s Quail Breed With New Rolling Mechanism System / Mohd Badli Ramli...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (3). pp. 78-88. ISSN 18235514 (Submitted)

Ramli, Mohd Ikram and Sulong, Abu Bakar and Muhamad, Norhamidi and Muchtar, Andanastuti and Zakaria, Mohd Yusuf (2017) Rheological Properties Of Titanium Alloy (Ti6Al4V) – Wollastonite (W) Composite Using Palm Stearin as Based Binder / Mohd Ikram Ramli...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 3 (2). pp. 87-96. ISSN 18235514

Rashid, Helmi and Omar, Abdul Rahman and Ahmad, Ismail Nasiruddin and Mohamed, Zulkifli and Wan Fauzi, Wan Muhammad Syahmi and Mahmud, Zamalia and Haron, Rohani (2017) Motorcyclists’ Prolonged Riding Simulation: The Setup and Procedures / Helmi Rashid ... [et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (5). pp. 197-208. ISSN 18235514 (Submitted)

Razak, Zakaria and Sulong, Abu Bakar and Muhamad, Norhamidi and Md Radzi, Mohd. Khairol Fadzly and Tholibon, Dulina and Tharazi, Izdihar and Ismail, Nur Farhani (2017) Effect of Multi-walled Carbon Nanotube on Mechanical Properties of Kenaf/Polypropylene Composites / Zakaria Razak...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 3 (1). pp. 107-117. ISSN 18235514

Razali, Muhamad Magffierah and Ab.Rashid, Mohd Fadzil Faisae and Abdullah Make, Muhammad Razif (2017) Optimization of Automotive Manufacturing Layout for Productivity Improvement / Muhamad Magffierah Razali ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (1). pp. 171-184. ISSN 18235514

Remeli, Muhammad Fairuz and Rosli, Mohd Arif Fikri and Bhathal Singh, Baljit Singh (2017) Investigation of the Thermosyphon Performance for Different Working Fluids / Muhammad Fairuz Remeli ... [et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (5). pp. 144-152. ISSN 18235514

Rosdi, Nurain and Nik Yahya, Nik Norhafiza and Hassan, Rohana and Yasin, Mohd Hanafie and Abd Malek, Nor Jihan (2017) Tensile performance of half-lap timber nailed joint strengthened using CFRP sheet / Nurain Rosdi … [et al.]. (2017) Journal of Mechanical Engineering (JMechE), 14 (1). pp. 81-95. ISSN 1823-5514 ; 2550-164X

S., Jaichandar and K., Annamalai (2017) Experimental investigation on the influences of varying injection timing on the performance of a B20 JOME biodiesel fueled diesel engine / S. Jaichandar and K. Annamalai. (2017) Journal of Mechanical Engineering (JMechE), 14 (1). pp. 61-80. ISSN 1823-5514 ; 2550-164X

S., Manjunath and Ajay, Kumar (2017) Analysis the effectiveness of cryogenic treatment through roughness and temperature prediction using bonn technique / Manjunath.S and Ajay Kumar. (2017) Journal of Mechanical Engineering (JMechE), 14 (2). pp. 16-35. ISSN 1823-5514 ; 2550-164X

S., Prabhu and B.K., Vinayagam (2017) Optimization of robot plasma coating efficiency using genetic algorithm and neural networks / S.Prabhu and B.K.Vinayagam. (2017) Journal of Mechanical Engineering (JMechE), 14 (1). pp. 125-150. ISSN 1823-5514 ; 2550-164X

S. Z., M. Rasib and N. F., Muhamad and H, M. Akil and Z. A., A. Hamid (2017) Preparation and Characterization of pH- and Temperature-responsive by Different Composition Chitosan-P(MAA-co-NIPAM) Hydrogel for Drug Delivery System / S. Z. M. Rasib ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (2). pp. 123-133. ISSN 18235514

Saffar, Seha and Jamaludin, Zamberi and Jafar, Fairul Azni (2017) Investigating the Influences of Automated Guided Vehicles (AGVs) as Material Transportation for Automotive Assembly Process / Seha Saffar...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (1). pp. 47-60. ISSN 18235514

Salim, Salim Mkubwa and I. Romli, Fairuz and Besar, Jailani and Negin, Ozve Aminian (2017) A Study on Potential Physical Hazards at Construction Sites / Salim Mkubwa Salim ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (1). pp. 207-222. ISSN 18235514

Sharudin, Hazim and Abdullah, Nik Rosli and Mamat, A.M.I. and Zaharin, M.S.M and A.R., Asiah (2017) Experimental investigation on physicochemical properties of Iso-Butanol additive in methanol-gasoline blends / Hazim Sharudin ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 2 (1). pp. 1-15. ISSN 1823-5514 ; 2550-164X (Submitted)

Sharudin, Hazim and Abdullah*, Nik Rosli and M. Yusoff, M. N. A. and Masjuki, H. H. and M. Ali, Obed (2017) Investigation of the Emission Characteristics of Iso-Butanol Additives on Methanol-Gasoline Blends using Spark Ignition Engine / Hazim Sharudin ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (1). pp. 93-106. ISSN 18235514

Shing, Chee Lim and Weily, Khoo and Ching, Theng Koh (2017) Electrospinning of Polycaprolactone (PCL) and Gelatin Polymeric Fibers / Shing Chee Lim ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (3). pp. 246-254. ISSN 18235514

Sidik, Mohamad Fuad and Abdul Rahman, Siti Mariam and Wan Mohamed, Wan Mazlina (2017) Evaluation of Controller Strategies in Air Traffic Management for KLFIR Oceanic Sector / Mohamad Fuad Sidik ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (5). pp. 121-130. ISSN 18235514

Siva, Gopalakrishnan and Jamaludin, Ummu Kulthum (2017) Investigation on Different Types of Blood Glucose Control System / Siva Gopalakrishnan and Ummu Kulthum Jamaludin. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (2). pp. 135-152. ISSN 18235514

Sudjatmiko, djatmiko. mlg@gmail. com and Soenoko, Rudy and Suprapto, Agus and Choiron, Moch. Agus (2017) Surface roughness and roundness optimization on turning process of Aluminium Alloy with Taguchi Method / Sudjatmiko … [et al.]. (2017) Journal of Mechanical Engineering (JMechE), 14 (1). pp. 97-107. ISSN 1823-5514 ; 2550-164X

Sukindar, Nor Aiman and Mohd Ariffin, Mohd Kharul Anuar and Baharudin, B.T Hang Tuah and Jaafar, Che Nor Aiza and Shah Ismail, Mohd Idris (2017) Optimization of the Parameters for Surface Quality of the Open-source 3D Printing / Nor Aiman Sukindar...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 3 (1). pp. 33-43. ISSN 1823-5514 ; 2550-164X

Suresh, Sangeeth and Abdul Hamid, Darulihsan and Yazid, MZA and Che Daud, Nur Rusydina and Mohd Din, Nik Nur Liyana (2017) An Investigation into the Impact of Flexural Elastic Modulus on the Dimensional Instability in CNC Turning of Titanium Alloy Grade 5 - Ti6Al4V / Sangeeth Suresh...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 3 (2). pp. 73-85. ISSN 18235514

Talib, R.J. and Basri, M. Hisyam and Ismail, N.I. and Rabilah, R. (2017) Influence of Iron Oxide Powders on Braking Performance of Brake Friction Materials / R.J. Talib...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (1). pp. 129-142. ISSN 18235514

Tamjidillah, Mastiadi and Budi Santoso, Purnomo (2017) The Model of Optimization for Parameter in the Mixing Process of Water Treatment / Mastiadi Tamjidillah...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 2 (2). pp. 113-122. ISSN 1823-5514 ; 2550-164X

Tayser, Sumer Gaaz and Sulong, Abu Bakar and H. Kadhum, Abdul Amir (2017) Influence of Sulfuric Acid on the Tensile Properties of Halloysite Reinforced Polyurethane Composite / Tayser Sumer Gaaz...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 3 (1). pp. 1-10. ISSN 1823-5514 ; 2550-164X

Tham, Ghalib and Mohamad Nor, Nur Hafiez and Faruqi, Mohamad and Saedon, Juri (2017) Prediction of Weld Bead Geometry for Small-Wire Submerged Arc Welding in 1G position / Ghalib Tham...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 3 (2). pp. 145-156. ISSN 18235514

Tharazi, Izdihar and Muhamad, Norhamidi and Ismail, Nur Farhani and Md Radzi, Mohd Khairul Fadzly and Razak, Zakaria and Tholibon, Dulina and Akhtar, Majid Niaz (2017) Effects of Fiber Content and Processing Parameters on Tensile Properties of Unidirectional Long Kenaf Fiber Reinforced Polylactic-Acid Composite / Izdihar Tharazi...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 3 (1). pp. 65-76. ISSN 1823-5514 ; 2550-164X

Tholibon, Dulina and Sulong, Abu Bakar and Muhamad, Norhamidi and Ismail, Nur Farhani (2017) Optimization of Hot Pressing Process for Unidirectional Kenaf Polypropylene Composites by Full Factorial Design / Dulina Tholibon...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 3 (2). pp. 23-35. ISSN 18235514

Triyono, Sri Hastuti and Neng, Sri Suharty (2017) Shear Strength of the Mixed Adhesive Joint Silyl Modified Polymer-Epoxy in Single Lap Joint Aluminum Triyono / Sri Hastuti and Neng Sri Suharty. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (1). pp. 235-248. ISSN 18235514

U.Q.A., Mansor and A., Ismail and A., Yahya and N.F.A., Shafie and A. M., Som and A.H., Nour and R., Yunus (2017) Kinetic Study for Ultrasonic assisted Membrane Anaerobic System (UMAS) Treating Decanter Palm Oil Mill Effluent (POME) / Mansor U.Q.A....[et al.]. (2017) Special Issue 2017 Vol 1: Frontiers in Sustainable Energy Research for Humanity, SI 2 (2). pp. 45-56. ISSN 18235514

Ukwueze, Bonaventure Emeka and Sulong, Abu Bakar and Muhamad, Norhamidi and Sajuri, Zainuddin (2017) The Characterization and Rheological Investigation of Materials for Powder Injection Moulding / Ukwueze Bonaventure Emeka...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 3 (2). pp. 97-107. ISSN 18235514

Wan Fauzi, Wan Muhammad Syahmi and Omar, Abdul Rahman and Rashid, Helmi (2017) Enhancement of Postura MotergoTM: From an Ergonomic Motorcycle Test Rig to a Full-Scale Simulator / Wan Muhammad Syahmi Wan Fauzi ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (4). pp. 43-59. ISSN 18235514

Wan Fauzi, Wan Muhammad Syahmi and Omar, Abdul Rahman and Rashid, Helmi and Saman, AliasMohd (2017) Pillion Simulation System (PISIS): An Exclusive System for Simulating Pillion’s Motorcycling Experience / Wan Muhammad Syahmi Wan Fauzi...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (2). pp. 91-109. ISSN 18235514

Wan Iskandar Mirza, Wan Imaan Izhan and Abdul Rani, Muhamad Norhisham and Yunus, Mohd Azmi and Ahmad Basri, Ahmad Burhani and Mat Isa, Ahmad Azlan (2017) Frequency Based Substructuring Method for the Investigation of the Dynamic Behaviour of a Beam Structure / Wan Imaan Izhan Wan Iskandar Mirza ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (3). pp. 142-154. ISSN 18235514

Wan Mansor, Wan Nuha and Md Tahir, Nurul Hidayah and Abd Ghani, Jaharah and Che Haron, Che Hassan and Nuawi, Mohd Zaki and Rizal, Muhamad (2017) Tool Wear Condition Monitoring using Slip Ring and Accelerometer System in Milling AISI P20 Tool Steel / Wan Nuha Wan Mansor...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 3 (2). pp. 63-72. ISSN 18235514

Wan Zulkifli, Wan Amirul Shafiz and Mohd Rosli, Zulkifli and Mohamad Juoi, Jariah and Yusuf, Yusliza (2017) Effect of Nitriding Temperature and Nitriding Time on MgAZ91D Alloy / Wan Amirul Shafiz Wan Zulkifli...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 3 (2). pp. 177-184. ISSN 18235514

Weily, Khoo and Ching, Theng Koh and Shing, Chee Lim (2017) Synthetic and Natural Fibrous Scaffolds for Soft Tissue Engineering Applications / Weily Khoo ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (3). pp. 223-233. ISSN 18235514

Wirachman, Wisnoe and M. Nasir, Rizal E. and Saarani, Wan Aizad Mu and Mohd Saad, Nornashiha and Afiq Mamud, Mohd Amirul (2017) Wind Tunnel Tests of UiTM Blended Wing Body - Unmanned Aerial Vehicle (BWB-UAV) Prototype / Wirachman Wisnoe ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (3). pp. 234-245. ISSN 18235514

Wisnoe, Wirachman and Abd Rahman, Khairil Muhaimin (2017) Effect of nozzle depth to acoustic signals produced by a Ranque-Hilsch Vortex Tube / Wirachman Wisnoe and Khairil Muhaimin Abd Rahman. (2017) Journal of Mechanical Engineering (JMechE), 14 (2). pp. 93-108. ISSN 1823-5514 ; 2550-164X

Y.S., Kong and Abdullah, S. and Omar, M.Z. and Haris, S.M. and D., Schramm and T., Bruckmann (2017) The Need to generate a Force Time History Towards Life Assessment of a Coil Spring / Y.S. Kong...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (5). pp. 11-26. ISSN 18235514

Yaakob, Nurul Afizan and Ganesan, Hema Nanthini and Harun, Nurul Hatiqah and Raja Abdullah, Raja Izamshah and Kasim, Mohd Shahir (2017) Influence of Grinding Parameters on Surface Finish of Inconel 718 / Nurul Afizan Yaakob...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 3 (2). pp. 199-209. ISSN 18235514

Yunus, Mohd Azmi and Aziz Shah, Mohamad Azam Shah and Abdul Rani, Muhamad Norhisham and Wan Iskandar Mirza, Wan Imaan Izhan and Kushairi, Sahril (2017) Experimental and Finite Element Analysis of Laser Stitch Welded Structure / Mohd Azmi Yunus ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (3). pp. 155-162. ISSN 18235514

Yussuf, Ummu Raihan and Hashim, Hadzli and Johari, Juliana and Mohd Sampian, Ahmad Faiz and Abdullah, Noor Ezan and Khairuzzaman, Noor Aishah and Maskom, Mohamad Azrif (2017) Inference Analysis of Dry Rubber Content Capacitance Properties in Discriminating Type of Rubber Clones / Ummu Raihan Yussuf...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 2 (2). pp. 157-165. ISSN 1823-5514 ; 2550-164X

Yusuf, Yusliza and Jaafar, Abdul Rahim and Omar, Noririnah and Azlan, Umar Al Amani (2017) The Influence of Heat Treatment on the Microstructure and Hardness Properties of Ti6Al4V and MgAZ91D Alloys / Yusliza Yusuf...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 3 (2). pp. 167-176. ISSN 18235514

Zailan, Farrah Diyana and Ruey, Shan Chen and Ahmad, Sahrim and Shahdan, Dalila and Baharin, Khairunnisa Waznah (2017) Influence of Processing Conditions on Mechanical Behaviours of Thermoplastic Natural Rubber/ Polyaniline Blend / Farrah Diyana Zailan...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 3 (1). pp. 225-235. ISSN 18235514

Zailani, Ramlan and Kamarudin, Khairul Ashraf and Raja Deris, Raja Razuan and Ismail, Khudzir (2017) Enhancing Hydrogen Production From The Pyrolysis Of Oil Palm EFB by Alkali Metal Oxides / Ramlan Zailani ... [et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (5). pp. 236-246. ISSN 18235514

Zainudin, Azlan and Chee, Kiong Sia and Pauline, Ong and Narong, Oh Lai Ching and Muhd Nor, Nik Hisyamudin (2017) Potential of Palm Oil Fuel Ash (POFA) Layers as Secondary Raw Material in Porcelain Stoneware Application / Azlan Zainudin...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 2 (2). pp. 71-81. ISSN 1823-5514 ; 2550-164X

Zainudin, Mahfuzah and Ismail, Muhammad Hussain (2017) Characteristic Of The YTTRIA Stabilized Zirconia (YSZ) for Ceramic Injection Moulding by Using Palm Stearin as a Primary Binder / Mahfuzah Zainudin and Muhammad Hussain Ismail. (2017) Journal of Mechanical Engineering (JMechE), SI 3 (2). pp. 133-143. ISSN 18235514

Zakaria, Mohd Hafizu and Che Ghani, Saiful Anwar and Wan Harun, Wan Sharuzi and Zaulkafilai, Zuriadi and Mohamed, Siti Rohaida (2017) Fabrication of Aluminium Internally Cooled Cutting Tool by Means of Selective Laser Melting (SLM) / Mohd Hafizu Zakaria...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 3 (1). pp. 185-198. ISSN 18235514

Zakaria, Mohd Yusuf and Sulong, Abu Bakar and Ramli, Mohd Ikram and Raza, Muhammad Rafi (2017) Determination of Critical Powder Loading of Titanium-Hydroxyapatite with Powder Space Holder for Powder Injection Molding Feedstocks / Mohd Yusuf Zakaria...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 3 (1). pp. 11-21. ISSN 1823-5514 ; 2550-164X

Thesis

Abd Aziz, Siti Norazlini (2017) Effect of palm stearin as single based binder on properties of ceramic injection molded of hydroxyapatite for scaffold applications / Siti Norazlini Abd Aziz. (2017) Masters thesis, thesis, Universiti Teknologi MARA (UiTM).

Abd Manap, Muhammad Faris (2017) Mechanics of Total Hip Replacement (THR): The effect of inclination and anteversion angle on the performance of epoxy UHMWPE acetabular cup / Muhammad Faris Abd Manap. (2017) Masters thesis, thesis, Universiti Teknologi MARA.

Abdol Rahim @ Ibrahim, Abdul Hadi (2017) Computational modelling of mass transport and dynamic simulation of a high pressure polymer electrolyte membrane electrolyser / Abdul Hadi Abdol Rahim @ Ibrahim. (2017) PhD thesis, thesis, Universiti Teknologi MARA.

Abdul Kadir, Ros Atikah (2017) TiH2 microporous replication pseudo-elastic NiTi alloy by metal injection moulding / Ros Atikah Abdul Kadir. (2017) Masters thesis, thesis, Universiti Teknologi MARA.

Abdul Kadir, Ros Atikah (2017) TiH₂ microporous replication pseudo-elastic NiTi alloy by metal injection moulding / Ros Atikah Abdul Kadir. (2017) Masters thesis, thesis, Universiti Teknologi MARA.

Abdul Malik, Norjasween (2017) Development of interactive scenario using humanoid robot to assist rehabilitation for children with cerebral palsy / Norjasween Abdul Malik. (2017) Masters thesis, thesis, Universiti Teknologi MARA (UiTM).

Abdul Rahman, Farah Aimi (2017) Safety checklist to manage fatalities and accidents risk at telecommunication sites / Farah Aimi Abdul Rahman. (2017) Masters thesis, thesis, Universiti Teknologi MARA.

Ahmad, Anis Salwa (2017) Effect of polyurethane insole on standing using foot pressure measurement and finite element analysis / Anis Salwa Ahmad. (2017) Masters thesis, thesis, Universiti Teknologi MARA.

Assan, Naziratie Assrinie (2017) Impact response of tubular structure with internally stacked circular tubes / Naziratie Assrinie Assan. (2017) Masters thesis, thesis, Universiti Teknologi MARA (UiTM).

Busu, Nur'Amirah (2017) Integration of travel control system with traverse test rig for friction stir welding process / Nur'Amirah Busu. (2017) Masters thesis, thesis, Universiti Teknologi MARA (UiTM).

Hashim, Hafizan (2017) Bending collapse and energy absorption of conventional and insert-reinforced closed-hat-section beams / Hafizan Hashim. (2017) PhD thesis, thesis, Universiti Teknologi MARA.

Hassin, Nor Munirah (2017) The reconciled finite element model of riveted joints structure for crash analysis / Nor Munirah Hassin. (2017) Masters thesis, thesis, Universiti Teknologi MARA (UiTM).

Johar, Khairunnisa (2017) Classification of brain activity using muscle activation marker for BCI controlled hand prosthesis / Khairunnisa Johar. (2017) Masters thesis, thesis, Universiti Teknologi MARA (UiTM).

Kamardin, Nur Kamarliah (2017) Mechanical properties and fracture toughness of polypropylene reinforced kenaf fibre and nanoclay composites / Nur Kamarliah Kamardin. (2017) Masters thesis, thesis, Universiti Teknologi MARA.

Mali, Mohamad (2017) Simulation and failure analysis of fibre-reinforced composite laminates under various load and boundary conditions / Mohamad Mali. (2017) Masters thesis, thesis, Universiti Teknologi MARA (UiTM).

Md Elias, Husna (2017) Synthesis and characterization of biomorphic silicon carbide from wood powders precursors / Husna Md Elias. (2017) Masters thesis, thesis, Universiti Teknologi MARA.

Mohamad, Nor Syahirah (2017) Tribological characteristics of different lubricants with titanium oxide nanoparticles additives / Nor Syahirah Mohamad. (2017) Masters thesis, thesis, Universiti Teknologi MARA (UiTM).

Mohamad Basir, Muhamad Hafizuddin (2017) Enhancement of wear properties 316L stainless steel through shot blasting treatment and paste boronizing process / Muhamad Hafizuddin Mohamad Basir. (2017) Masters thesis, thesis, Universiti Teknologi MARA (UiTM).

Mohamed, Mohamed Ackiel (2017) Fatigue life enhancement for friction stir welded AA6061 butt joint through high frequency mechanical impact (HFMI) of pneumatic impact treatment (PIT) / Mohamed Ackiel Mohamed. (2017) PhD thesis, thesis, Universiti Teknologi MARA (UiTM).

Mohd Razif, Nur Hidayah (2017) Heat transfer analysis for ammonia-water mixture heat exchanger for organic rankine cycle of an energy recovery system / Nur Hidayah Mohd Razif. (2017) Masters thesis, thesis, Universiti Teknologi MARA (UiTM).

Othman, Mohd Hakimi (2017) The investigation and reconciliation of the dynamic characteristics of a thin plate laser spot welded joint structure / Mohd Hakimi Othman. (2017) Masters thesis, thesis, Universiti Teknologi MARA (UiTM).

Othman, Nurul Atiqah (2017) Integration of programmable logic controller (PLC) into part-task trainer of upper limb spasticity simulator / Nurul Atiqah Othman. (2017) Masters thesis, thesis, Universiti Teknologi MARA (UiTM).

Sapiai, Napisah (2017) Mechanical and wear properties of functionalised carbon nanotubes modified kenaf composites / Napisah Sapiai. (2017) PhD thesis, thesis, Universiti Teknologi MARA (UiTM).

Shaari @ Md Noh, Nor Shamimi (2017) Thermal conductivity and wear behaviour of copper matrix composites reinforced with carbon nanotubes using powder metallurgy route / Nor Shamimi Shaari @ Md Noh. (2017) Masters thesis, thesis, Universiti Teknologi MARA.

Surianirizal, Najiy Rizal (2017) Multi-cavity mould design and simulation of polyethylene terephthalate (PET) plastic parison / Najiy Rizal Surianirizal. (2017) Masters thesis, thesis, Universiti Teknologi MARA (UiTM).

Syafiq Khalid, Muhamad Faris (2017) Mechanical properties of treated arenga pinnata fibre reinforced nanomodified epoxy composite / Muhamad Faris Syafiq Khalid. (2017) Masters thesis, thesis, Universiti Teknologi MARA (UiTM).

Wan Iskandar Mirza, Wan Imaan Izhan (2017) The frequency based substructuring scheme for the investigation of the dynamic behaviour of a structure with bolted joints / Wan Imaan Izhan Wan Iskandar Mirza. (2017) Masters thesis, thesis, Universiti Teknologi MARA (UiTM).

Zaharudin, Aznifa Mahyam (2017) Optimization and tribological properties of semi metallic friction materials / Aznifa Mahyam Zaharudin. (2017) PhD thesis, thesis, Universiti Teknologi MARA (UiTM).

Zainol, Muhd Azhar (2017) Numerical analysis on the effect of upstream building arrangement and setback distance on pedestrian wind environment / Muhd Azhar Zainol. (2017) Masters thesis, thesis, Universiti Teknologi MARA (UiTM).

Zainudin, Mahfuzah (2017) Rheological and mechanical properties of Yttria Stabilized Zirconia (YSZ) produced by ceramic injection moulding / Mahfuzah Zainudin. (2017) Masters thesis, thesis, Universiti Teknologi MARA.

Entrepreneurship Project

Abd Halim, Muhammad Shameerul Afif and Abd Halim, Muhammad Shameerul Akif and Zurkarnain, Luqman Arif (2017) Technology Entrepreneurship (ENT600) Smart shoe cleaner machine / Muhammad Shameerul Afif Abd Halim, Muhammad Shameerul Akif Abd Halim and Luqman Arif Zurkarnain. (2017) [Entrepreneurship Project] (Unpublished)

Abd Halim, Muhammad Shameerul Afif and Zurkarnaim, Luqman Arif (2017) Smart shoe cleaner machine / Muhammad Shameerul Afif Abd Halim and Luqman Arif Zurkarnaim. (2017) [Entrepreneurship Project] (Unpublished)

Abdullah, Mohd Farhan and Zulkifli, Ahmad Haziq and Abdul Rahman, Mohamad Shahidan (2017) ENT600: Hillside tram / Mohd Farhan Abdullah, Ahmad Haziq Zulkifli and Mohamad Shahidan Abdul Rahman. (2017) [Entrepreneurship Project] (Unpublished)

Ahmad Halimi, Ahmad Hafiz Asyraf and Shipulizan, Alif Syazril and Kanaludin, Mohd Razin (2017) ENT600 : Smart aromatic atomizer / Ahmad Hafiz Asyraf Ahmad Halimi, Alif Syazril Shipulizan and Mohd Razin Kanaludin. (2017) [Entrepreneurship Project] (Unpublished)

Ahmad Halimi, Ahmad Hafiz Asyraf and Shipulizan, Alif Syazril and Kanaludin, Mohd Razin (2017) Smart aromatic atomizer / Ahmad Hafiz Asyraf Ahmad Halimi, Alif Syazril Shipulizan and Mohd Razin Kanaludin. (2017) [Entrepreneurship Project] (Unpublished)

Ismail, Amsyar Wajdi and Affandi Adnan, Muhamad Helmi and Mohd Pooad, Mohammad Zarriq Adzrin (2017) Entrepreneurship Technology (ENT600) Ergonomic wheelbarrow / Amsyar Wajdi Ismail, Muhamad Helmi Affandi Adnan and Mohammad Zarriq Adzrin Mohd Pooad. (2017) [Entrepreneurship Project] (Unpublished)

Kamarul Zaman, Muhammad Syakir and Yahya, Mohd Fazrydeen (2017) Electro-strip / Muhammad Syakir Kamarul Zaman and Mohd Fazrydeen Yahya. (2017) [Entrepreneurship Project] (Unpublished)

Mohamad Khalid, Mohamad Moor Ariffin and Mohd Kamal, Muhammad Ikmal Naim and Nik Dziauddin, Nik Amirul Khalid (2017) Technology Entrepreneurship (ENT600) Technology blueprint smart wheelchair / Mohamad Moor Ariffin Mohamad Khalid, Muhammad Ikmal Naim Mohd Kamal and Nik Amirul Khalid Nik Dziauddin. (2017) [Entrepreneurship Project] (Unpublished)

Mohd Poaad, Mohammad Zarriq Adzrin and Ismail, Amsyar Wajdi and Adnan, Muhammad Helmi Affandi (2017) ENT600: Smart wheelbarrow / Mohammad Zarriq Adzrin Mohd Poaad, Amsyar Wajdi Ismail and Muhammad Helmi Affandi Adnan. (2017) [Entrepreneurship Project] (Unpublished)

Yahya, Mohd Fazrydeen and Kamarul Zaman, Muhammad Syakir (2017) Electro-strip / Mohd Fazrydeen Yahya and Muhammad Syakir Kamarul Zaman. (2017) [Entrepreneurship Project] (Unpublished)