Items where Subject is "Metal manufactures. Metalworking"

Group by: Creators | Item Type
Number of items at this level: 97.

Article

Fatigue Life Assessment of 9mm Thickness Low Carbon Steel with Multi-Objective Optimized Welding Process / Azrriq Zainul Abidin...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (1). pp. 143-153. ISSN 18235514

Specific energy absorption study on external inversion of metal tubes / Mohd Rozaiman Aziz and Roslan Ahmad. (2007) ESTEEM Academic Journal, 3. pp. 3-13. ISSN 1675-7939

Springback analysis of thin tubes under torsional loading / Vikas Kumar Choubey, Mayank Gangwar and J. P. Dwivedi. (2010) Journal of Mechanical Engineering (JMechE), 7 (2). pp. 81-102. ISSN 1823-5514 ; 2550-164X

Springback analysis of thin tubes with arbitrary stress-strain curves / Mayank Gangwar … [et al.]. (2011) Journal of Mechanical Engineering (JMechE), 8 (1). pp. 57-76. ISSN 1823-5514 ; 2550-164X

Microstructural and Mechanical Properties of Underwater Wet Welded SS400 Steel / N. M. L. P. K. Yasari ...[et al.]. (2018) Journal of Mechanical Engineering (JMechE), SI 5 (3). pp. 168-179. ISSN 18235514

Comparison of different surface pre-treatment on mild steel for cobalt-nickel-iron electroplating / Koay Mei Hyie … [et al.]. (2023) Journal of Mechanical Engineering (JMechE), 20 (3): 13. pp. 263-278. ISSN 1823-5514 ; 2550-164X

Accumulation and health risk of heavy metals in local and imported fish (rastrelliger kanagurta) sold in Shah Alam, Selangor / Nadiatul Syima Mohd Shahid [et al.]. (2021) Borneo Akademika, 5 (2): 18. pp. 184-193.

Comparative Distortion Analysis of Welded T-Joint between 2D-Shell and 3D-Solid Element using FEA with Experimental Verification / Keval. P Prajadhiana...[et al.]. (2018) Journal of Mechanical Engineering (JMechE), SI 5 (2). pp. 99-115. ISSN 18235514

Parameter optimization of metal injection moulding : A review / M Prathabrao ... [et al.]. (2018) Journal of Mechanical Engineering (JMechE), SI 5 (6). pp. 100-114. ISSN 18235514

An investigation into the Metal Grinding Process under Sub-Zero Temperature Cutting Fluid / Richard P. Daisley and Boppana V. Chowdary. (2011) Journal of Mechanical Engineering (JMechE), 8 (1). pp. 1-24. ISSN 1823-5514 ; 2550-164X

Additive Manufacturing of Copper-ABS Filament by Fused Deposition Modeling (FDM) / N Sa’ude ...[et al.]. (2018) Journal of Mechanical Engineering (JMechE), SI 5 (4). pp. 23-32. ISSN 18235514

A study on electroplating / Saidatulakmar Shamsuddin. (2003) Jurnal Intelek, 1. pp. 94-103. ISSN 2231-7716

A preliminary study using the Energy Dispersive X-Rays (EDX) technique on the electroless plated ceramic body / Saidatulakmar Shamsuddin ... [et al.]. (2004) Jurnal Intelek, 2 (1). pp. 20-30. ISSN 2231-7716

ICP analysis of heavy metals in Meretrix SPP from Pantai Sepat, Kuantan, Pahang / Nurul Izzah Humairah Sharrudin … [et al.]. (2023) Borneo Akademika, 7 (2). pp. 77-84. ISSN 2462-1641

Development of prediction system model for mechanical property in friction stir welding using Support Vector Machine (SVM) / Arman Syah ... [et al.]. (2018) Journal of Mechanical Engineering (JMechE), SI 5 (5). pp. 216-225. ISSN 18235514

Effect of laser energy on weld strength for neodymium yttrium aluminum garnet (ND:YAG) AT λ = 1.06 μm / Khairi Khazman Zulkiflee and Nurul Sabihah Zakaria. (2021) Journal of Academia, 9. pp. 145-153. ISSN 2289-6368

Book Section

Tannin extraction from mangosteen peel for viscosifier and fluid loss additive in drilling fluid / Nurul Aimi Ghazali … [et al.]. (2014) In: IIDEX 2014: invention, innovation & design exposition. Research Innovation Business Unit, Shah Alam, Selangor, p. 102.

PDE-based denoising tool for digital radiographic image of welding defect / Tuan Nurul Norazura Tuan Sulong … [et al.]. (2014) In: IIDEX 2014: invention, innovation & design exposition. Research Innovation Business Unit, Shah Alam, Selangor, p. 93. (Submitted)

Conference or Workshop Item

High temperature corrosion behaviour of steel with a carbonate deposit at 1123k / Habsah Md Ishak … [et al.]. (2008) In: Proceedings STSS 2008, 3-4 June 2008, M.S. Garden Hotel, Kuantan Pahang.

Preliminary stage development of portable steel chamfering machine / Sia Chee Kiong, Ker Eng Ling and Phang Chang. (2006) In: Volume No. 1: Science and Technology, 30 – 31 May 2006, Swiss Garden Resort & Spa Kuantan, Pahang.

Thesis

TiH2 microporous replication pseudo-elastic NiTi alloy by metal injection moulding / Ros Atikah Abdul Kadir. (2017) Masters thesis, thesis, Universiti Teknologi MARA.

TiH₂ microporous replication pseudo-elastic NiTi alloy by metal injection moulding / Ros Atikah Abdul Kadir. (2017) Masters thesis, thesis, Universiti Teknologi MARA.

Investigation of relationship between weld cost and types of arc welding process / Noor Akmar Aman. (2009) Degree thesis, thesis, Universiti Teknologi MARA.

Effect of loading rates on the fracture toughness of fiber metal laminate kenaf short fiber/epoxy/polyester / Eldridge George. (2009) Degree thesis, thesis, University Teknologi MARA Shah Alam.

Scrap metal management system (SMMS) / Mohd Fadhil Ibrahim. (2014) Degree thesis, thesis, Universiti Teknologi MARA (UiTM).

Improvement of traditional gold recovery process for jewellery scrap / Saadiah Kaspin. (2008) Masters thesis, thesis, Universiti Teknologi MARA (UiTM).

Kemasyhuran pertukangan perak di Kelantan / Mohd Nor Irwan Maihadi. (2001) Degree thesis, thesis, Universiti Teknologi MARA, Kelantan.

Mechanical and grain growth behaviour of wire-arc additive manufacturing (WAAM) of SS316L using experiment and numerical simulation / Muhd Faiz Mat @ Muhammad. (2022) PhD thesis, thesis, Universiti Teknologi MARA (UiTM).

Comparison between the estimated and actual productivity for the fabrication of a steel framework / Mohd Zukarnan Mat Deraseh. (2010) Degree thesis, thesis, Universiti Teknologi MARA.

Computational fluid dynamics (CFD) simulation of triple exposure solar oven / Mohd Fadhli Mat Zain. (2010) Degree thesis, thesis, Universiti Teknologi MARA (UiTM).

Penggunaan cincin perak bermotif bunga ketumbit dan pucuk kacang di kalangan remaja / Hafizul Moideen. (2001) Degree thesis, thesis, Universiti Teknologi MARA, Kelantan.

Ukiran bentuk cincin melambangkan imej kepada pemakai / Azizan Muhamad Asyri. (2001) Degree thesis, thesis, Universiti Teknologi MARA, Kelantan.

Pengaplikasian motif tradisional pada cincin lelaki tinjauan di Pantai Timur / Mazuin Mustafa. (2001) Degree thesis, thesis, Universiti Teknologi MARA, Kelantan.

Pengaplikasian motif - motif tradisional dan moden pada barangan kemas perak / Fidrouz Nasaruddin. (2001) Degree thesis, thesis, Universiti Teknologi MARA, Kelantan.

The strengthening of aluminium 2024 sheet by accelerated aging / Syafruddin Noer. (2007) Masters thesis, thesis, Universiti Teknologi MARA.

Development of an expert system for sheet-metal-forming die manufacturing methodologies to support an extended design team / Raja Aziz Raja Ma’arof. (2006) PhD thesis, thesis, Universiti Teknologi MARA.

Pengaplikasian motif kartun pada kerongsang untuk penggunaan kanak-kanak / Norafzan Shafii. (2001) Degree thesis, thesis, Universiti Teknologi MARA, Kelantan.

Work study on industrial production in x-member assembly SRM 24 (welding) at Tracoma Sdn. Bhd. / Wan Mohammad Fadhli Wan Hapandi. (2009) Degree thesis, thesis, Universiti Teknologi MARA.

Nilai-nilai estetika didalam pembuatan barangan pewter / Nor Azizah Yaacob. (1998) Degree thesis, thesis, Universiti Teknologi MARA (UiTM).

Perkembangan industri tembaga di Terengganu / Tajudin Yasin. (2001) Degree thesis, thesis, Universiti Teknologi MARA, Kelantan.

Heat treatment of iron and steel / Nasri Yusoff. (1985) Diploma thesis, thesis, Institut Teknologi MARA.

Penggunaan rekabentuk jenis estetik dalam barangan tembaga di Pantai Timur / Zuraine Yusoff @ Daud. (2001) Degree thesis, thesis, Universiti Teknologi MARA, Kelantan.

Software development of welding procedure specification for flux cored arc welding / Huzaymi Zamri. (2006) Degree thesis, thesis, Universiti Teknologi MARA.

Student Project

Design and analysis of manufacturing facilities for friction stir welding process / Muhammad ‘Afwan Ab Razak. (2017) [Student Project] (Unpublished)

Brassware cottage industry in Kuala Terengganu permanent mould design and diversification / Osman Ab.Rahman and Mohd.Faudzir Abu Bakar. (1985) [Student Project] (Unpublished)

Kajian masa dan kaedah pengukuran masa / Rizalman Abd. Rahim and Muhammad Amin Ahmad Tajudin. (1997) [Student Project] (Unpublished)

Arduino welding table / Adli Adham Abdul Hakim. (2022) [Student Project] (Submitted)

Keselamatan dan kesihatan di tempat kerja dalam industri pembuatan logam / Rosli Abdullah and Mohd. Laili Sanusi. (1997) [Student Project] (Unpublished)

Design and development of the catapult based on cotton ball launcher / Muhammad Asmadi Abdunkarim Yakoh@Ab Karim. (2022) [Student Project] (Submitted)

Wheel sprayer / Abdullah Muhammad Al-Wahiduddin Adnan. (2022) [Student Project] (Submitted)

Upper bearing blank / Mohd Faizal Ahmad and Mohd Sufian Anuar. (2002) [Student Project] (Unpublished)

Thermal analysis on exhaust pipe of LPG combustor / Muhammad Hadie Aizzuddin Asli. (2022) [Student Project] (Unpublished)

Design of a product by cold forging / Daneil Awan, Jalani Embik and Roy Hannis. (1997) [Student Project] (Unpublished)

Safety box delivery / Muhammad Haziq Azman ... [et al.]. [Student Project] (Unpublished)

Study of hardness properties of butt welded joints using Metal Inert Gas (MIG) welding on mild steel plate / Muhammad Syahir Azman. (2022) [Student Project] (Unpublished)

Noise exposure and hearing loss in a steel industry / Muhammad Ismail Harun. (2012) [Student Project] (Unpublished)

Fabrication of miniature foldable iron board / Muhammad Hadzrey Hasmi. (2022) [Student Project] (Unpublished)

Pereka logam halus sebagai satu kerjaya / Siti Hasniza Husain. (2001) [Student Project] (Unpublished)

Case study in sheet metal forming of bracket stabilizer / Ahmad Ismail Kamsah and Mohd Zainudin Mah Hasan. (2001) [Student Project] (Unpublished)

Electronic clock, azan reader, and ringer (digital clock) / Mohd Khairil Adzhar Mahmood and Mohd Nirwan Aliasa’a. (2005) [Student Project] (Unpublished)

Design electronic clock with azan reader and ringer / Ikhwan Mat Yasin @ Hashim and Kamaruzzaman Mat Rani. (2005) [Student Project] (Unpublished)

Study of hardenability of mild steel and medium carbon steel by Jominy test / Muhammad Aiman Hafizin Mazlan. (2022) [Student Project] (Submitted)

Welding demontration table with adjuster / Muhammad Arid Azwar Mazuadi. (2022) [Student Project] (Submitted)

Effect of microstructure on low carbon steel due to variable temperature using plasma cutting / Ahmad Shakell Naim Md Sanusi. (2022) [Student Project] (Unpublished)

Multipurpose stationary set / Muhammad Zulkhairee Md Zabani ... [et al.]. (2015) [Student Project] (Unpublished)

The investment casting process of optimization / Md. Khairul Fadli Mestor, Khir Johari Ismail and Mohd Fahmi Hasan. (2005) [Student Project] (Unpublished)

Design an electronic azan clock, reader and ringer / Mohammad Ekmal Mohammad Hatta and Azhar Saffuan Ramli. (2005) [Student Project] (Unpublished)

Study of hardness on the mild steel in various cooling medium / Haziq Shazwan Mohd Ghazali. (2022) [Student Project] (Submitted)

Digital clock and Azan reader / Mohd Anuar Mohd Hasan and Syed Muhd. Abd. Matin Syed Mat Daud. (2005) [Student Project] (Unpublished)

The study of the recycling pattern metals in Malaysia / Ahmad Faris Mohd Salleh and Omar Bapokutty. (1997) [Student Project] (Unpublished)

Study of hardness properties of buttwelded joints using Shield Metal Arc Welding (SMAW) on mild steel plate / Nur Ain Syuhada Syafika Mohd Syukri. (2022) [Student Project] (Unpublished)

Design and fabrication of adjustable spanner / Muhammad Amyrul Azri Mohd Zain. (2022) [Student Project] (Unpublished)

Pengkajian dan pembuatan pintu-pintu gril bagi industri-industri kecil di Malaysia / Mazhar Muhammad and Azmi Ghazali. (1989) [Student Project] (Unpublished)

Study the effect of injection pressure with density using hot chamber die-casting machine / Asraf Muhd Ma’asus and Mohd Norazlishah Mohd Ali. (2005) [Student Project] (Unpublished)

Magnetic ceramic / Ahmad Zaidi Mukhayok … [et al.]. (1997) [Student Project] (Unpublished)

Exposure of fine particulate matter (PM₂.₅) in automotive industry among fitting line workers and health risk assessment / Nurfatihah Mustaffa. (2018) [Student Project] (Unpublished)

Study of MIG metal transfer / Ahmad Ezan Mustapha and Hanizan Mohd Husin. (1992) [Student Project] (Unpublished)

Study of hardness properties of buttwelded joints using Shield Metal Arcwelding (SMAW) on stainless steel plate / Nik Mohamad Aqeel Nik Mohamad Kariman. (2022) [Student Project] (Submitted)

The influence of thickness on mild steel in rapid cooling process / Nik Iqlima Nik Mohd Zaki. (2022) [Student Project] (Submitted)

Study of hardness propeties of butt welded joints using Metal Inert Gas (MIG) welding on stainless steel plate / Muhammad Izzat Hakimi Rosli. (2022) [Student Project] (Unpublished)

The influence of hydrogen environment on mild steel welds / Muhammad Sukhri Russelan. (2017) [Student Project] (Unpublished)

Rekacorak pada permukaan barangan logam perak Melayu / Muhamad Muhar Suhaimi. (1999) [Student Project] (Unpublished)

Effect of processing parameters in fabrication of Co-Ni- Fe coated mild steel for welding plate application \ Mohd Adham Akmal Tukiran. (2016) [Student Project] (Unpublished)

Portable sieve for greensand and cast Damascus steel knife / Wan Muhammad Adli Mustaqim Wan Ibrahim. (2022) [Student Project] (Submitted)

The influence of geometry specimens on mild steel in slow cooling process / Muhammad Amar Zulhaikal Zamre. (2022) [Student Project] (Submitted)

Entrepreneurship Project

Rocky Eyewear / Imran Danial Ahmad Latif. (2021) [Entrepreneurship Project] (Unpublished)

Sassa Enterprise / Siti Rokiah Daud... [et al.]. (1999) [Entrepreneurship Project] (Unpublished)

Delaq Design Sdn. Bhd. / Rosmawati Awang ... [et al.]. (2002) [Entrepreneurship Project] (Unpublished)

ENT 530 Social Media Portfolio: Outskiray / Nur Hanisah Badrolsham. (2021) [Entrepreneurship Project] (Unpublished)

Strawvenger / Syazarisya Hud. (2021) [Entrepreneurship Project] (Submitted)

ENT 530 Business Plan / Aina Khairunnisa Mohd Zalani. (2021) [Entrepreneurship Project] (Submitted)

Step Up Corparation : Portable Ladder / Aiman Hanifi Radzuan ...[et al.]. (2016) [Entrepreneurship Project] (Unpublished)

ENT 530 Social Media Portfolio: Vintage Watch 98 / Muhammad Imran Shahril. (2021) [Entrepreneurship Project] (Unpublished)

AZAZ’S Industries (M) Sdn. Bhd. (Pengeluaran Skru) / Ahmad Suhaimi Sulaiman ... [et al.]. (1998) [Entrepreneurship Project] (Unpublished)

Northen Star Enterprise (Aluminium Product) / Wan Jama’aini Wan Hamid... [et al.]. (2003) [Entrepreneurship Project] (Unpublished)

Research Reports

Experimental study of composite cold-formed steel c-section connected back-to-back / Mohamad Rohaidzat Mohamed Rashid, Noorsaidi Mahat and Nazri Nasir. (2009) [Research Reports] (Unpublished)

Other

Evaluation and analysis various types of welding imperfections collected from the steel fabricators / Wan Muhd Adham Wan Ahmad. UNSPECIFIED. (Submitted)

This list was generated on Thu Mar 28 23:40:45 2024 UTC.