Items where Subject is "Machine tools and machining"

Article

Characterisation of Stress Intensity Factor with Magnetic Flux Signal Leakage in Stable Fatigue Crack Growth Region S. R. Ahmad ...[et al.]. (2018) Journal of Mechanical Engineering (JMechE), SI 5 (3). pp. 141-155. ISSN 18235514

V-shaped bending support’ membantu dalam eksperimen ‘3-point bending test’ untuk tikus bersaiz kecil (V-shaped bending support helps in 3-point bending test experiment for small mice bone) / Noor Shafini Mohamad and Mohd Hafizi Mahmud. (2020) Jurnal Inovasi Malaysia (JURIM), 4 (1). pp. 1-14. ISSN 2600-7606

Fine Bone China Product using Ceramics Slip Rotary Moulding (CSRM) Technique / Norazne Nasir ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (4). pp. 31-42. ISSN 18235514

Influences of main machining process parameters and tool wear on the machining damage generated during edge milling CFRP composites / Nguyen Thi-Hue and Nguyen Dinh-Ngoc. (2023) Journal of Mechanical Engineering (JMechE), 20 (3): 18. pp. 355-370. ISSN 1823-5514 ; 2550-164X

Book Section

PVACLAMP: Portable Vacuum Clamping for Tool Room / Norfariza Ab Wahab … [et al.]. (2017) In: Melaka International Intellectual Exposition (MIIEX 2017). Division of Research and Industry Linkages, Alor Gajah, Melaka.

Development of thermostable microencapsulated lactobacillus targeted gut delivery / Muhamad Fareez Ismail. (2018) In: The Doctoral Research Abstracts. IPSis Biannual Publication, 14 (14). Institute of Graduate Studies, UiTM, Shah Alam.

Design and innovation of chuck for lathe machine / Muhamad Faiz Jofri ... [et al.]. (2017) In: Melaka International Intellectual Exposition (MIIEX 2017). Division of Research and Industry Linkages, Alor Gajah, Melaka.

Steering Wheel Alignment JIG / Norakmal Maamor … [et al.]. (2012) In: RIID 2012: Innovation For Sustainable Growth. Bahagian Penyelidikan dan Jaringan Industri, UiTM Melaka, Alor Gajah, p. 35. (Unpublished)

Bending and cutting links hand tools / Zamali Omar, Ayu Wirdawati Po'a and Siti Marlinna Chu Mohd Rizal Chu. (2012) In: RIID 2012: Innovation For Sustainable Growth. Bahagian Penyelidikan dan Jaringan Industri, UiTM Melaka, Alor Gajah, Melaka, p. 48.

Conference or Workshop Item

Smart grass cutter/ Muhammad Hifzhan Ruslan, Muhammad Ammar Maznan and Yusri Aizat Mohd Yasir Afkam. (2018) In: Electrical Engineering Innovation Competition & Exhibition (EEICE) 2018, 13-14 November 2018, Dewan Aspirasi, UiTM Cawangan Terengganu.

Effect of cutting fluid pressure on machining of AISI 304 performances / Zainal Arifin Selamat and Mohd Razali Muhamad. (2008) In: Proceedings STSS 2008 Broadening Horizons Through Research Science and Technology, 3-4 June 2008, M.S. Garden Hotel, Kuantan Pahang.

Thesis

Performance analysis of thermal arc spray aluminium coating as a sacrificial anode / Muhamad Hafiz Abd Malek. (2015) Masters thesis, thesis, Universiti Teknologi MARA.

A study of the effects of machining parameters on the surface roughness in the turning process / Nor Akram Abdullah. (2010) Degree thesis, thesis, Universiti Teknologi MARA (UiTM).

Study on machining tungsten carbide with electrical discharge machining (EDM) using Taguchi method / Mohd Rahimatul Azwa Che Rahim. (2009) Degree thesis, thesis, Uinversiti Teknologi MARA (UiTM).

Effects of prosthesis stem length on stress distribution in cementless hip arthroplasty / Emmi Farisa Jaafar. (2009) Degree thesis, thesis, Universiti Teknologi MARA Shah Alam.

Design and development of frictionless automotive transmission: power transmission analysis with virable speed motor / Din Iqbal Mahar Afandi. (2009) Degree thesis, thesis, Universiti Teknologi MARA Shah Alam.

Three dimensional cutting force and tool deflection in micro-end milling AISI D2 / Noor Aniza Norrdin. (2016) Masters thesis, thesis, Universiti Teknologi MARA.

A study of design new method cutting metal plate lead / Abdull Hadi Salleh. (2009) Degree thesis, thesis, Universiti Teknologi MARA Shah Alam.

Implementing loops system for controlling tool movement / Muhammad Faizul Rizal Zainal Alam. (2010) Degree thesis, thesis, Universiti Teknologi MARA.

Student Project

Optimization of wire cut EDM process parameters using response surface methodology (RSM) / Muhamad Razwan Abdul Aziz. (2017) [Student Project] (Unpublished)

Laboratory manual for Plant Engineering / Muhamad Faiz Abu Zaki and Mohd Alijufri Bastani. (2005) [Student Project] (Unpublished)

Study of hardness properties of butt welded joints using Metal Inert Gas (MIG) welding on mild steel plate / Muhammad Syahir Azman. (2022) [Student Project] (Unpublished)

Influence of carbon addition on sintering behaviour in ultrafine wc-co Powder / Aidilrizam Azmi. (2017) [Student Project] (Unpublished)

Development of graphical user interface for milling machine energy prediction tool / Muhammad Ikmal Hakim Badrulsham. (2020) [Student Project]

The effect of machining parameters on surface integrity of aluminium material using lathe machine / Fakhrul Adam Fazilan. (2022) [Student Project] (Submitted)

The effect of machining parameters on surface integrity of mild steel material using lathe machine / Faiz Azzhar Hamzah. (2022) [Student Project] (Submitted)

Investigation of jolt squeeze machine specifications for dumbell design production and its characterizations / Muhammad Danish Haikal Hamzah. (2024) [Student Project] (Unpublished)

Comparative cost between manual and mechanize of harvesting technique in oil palm plantation / Muhammad Syahmi Haris Suhairi. (2015) [Student Project] (Unpublished)

Effect of carbon addition and VC on mechanical properties in ultra-fine WC-Co cutting tool / Nurul Nazihah Ismail. (2017) [Student Project] (Unpublished)

Process modelling and simulation for prediction of chip morphology during machining of stainless steel / Lafishahzreen Maharam. (2017) [Student Project] (Unpublished)

Design and fabrication of potato cutter machine / Muhammad Aidil Azzam Mat Nasir. (2022) [Student Project] (Submitted)

Rotating Chicken Skewer / Khirwizam Md Hkhir and Nursharulhamir Johari. (2003) [Student Project] (Unpublished)

Upgrading of blending process for sand casting / Mohamad Hanafiah Mohamed Ali and Bushra Mokhtar. (2005) [Student Project] (Unpublished)

Pattern design for investment casting / Mohammad Naimie Mohamed Bakari and Rosniza Rabilah. (2005) [Student Project] (Unpublished)

Modeling bolt behavior using finite element analysis / Jumatirah Mohd Alias. (2006) [Student Project] (Unpublished)

Failure mode and effects analysis in manufacturing of milling process / Mohd Aslam Mohd Azaha. (2022) [Student Project] (Unpublished)

Study of hardness on the mild steel in various cooling medium / Haziq Shazwan Mohd Ghazali. (2022) [Student Project] (Submitted)

Design and development of sling based on ping pong ball launcher / Muhammad Luq Ai Mohd Hassim. (2022) [Student Project] (Submitted)

Design of punch and die for trimming operation / Muhammad Asyraf Mohd Lizam. (2022) [Student Project] (Submitted)

Automatic flour sifter / Alya Husna Mohd Shukry. (2022) [Student Project] (Unpublished)

Investigation on PETG tensile properties through 3D printing / Muhammad Syazrul Mohd Zahari. (2020) [Student Project] (Unpublished)

The effect of machining parameters on surface integrity of aluminium material using vertical milling machine / Abdul Azim Mohd Zaidi. (2022) [Student Project] (Submitted)

Mesin membanting padi / Zaibri Muhamad and Nik Mohd Nirman Mansor. (1995) [Student Project] (Unpublished)

Influence of carbon addition on mechanical properties in ultra-fine WC-Co cutting insert / Nur Atikah Muin. (2017) [Student Project] (Unpublished)

Design and analysis of mini extrusion machine for 3D printing filament / Ahmad Akmal Mustafa. (2020) [Student Project] (Unpublished)

Designing and fabricating a twin polishing machine / Nik Azizul Hisham Nik Abd Aziz and Nik Ahmad Sallehuddin Nik Mohammed. (1992) [Student Project] (Unpublished)

Study of hardness properties of buttwelded joints using Shield Metal Arcwelding (SMAW) on stainless steel plate / Nik Mohamad Aqeel Nik Mohamad Kariman. (2022) [Student Project] (Submitted)

Graphical user interface for surface roughness prediction of CNC milling machine / Muhammad Qayyum Nor Asffan. (2020) [Student Project]

Miniature drilling machine prototype / Muhammad Zakiruddin Osman @ Mohd Nordin. (2022) [Student Project] (Submitted)

Dimensional accuracy of abs 3D printed part using 3D Espresso F220 machine / Ahmad Afiq Aiman Roslan. (2020) [Student Project]

Alat pengupas kelapa / Affandi Rumpa and Dayang Fatimah Abang Shebli. (1996) [Student Project] (Unpublished)

An experimental investigation of TiCN tool life and tool wear in turning of titanium / Muhamad Anwar Salehudin. (2016) [Student Project] (Unpublished)

Hydraulic axle shaft puller with stand / Muhammad Luqman Hakim Salyazid. (2022) [Student Project] (Unpublished)

An experimental investigation of WC-Co tool life and tool wear in turning of titanium / Shamsiatun Shamsuddin. (2016) [Student Project] (Unpublished)

Toolbox trolley / Muhammad Adam Shamsul Harisah, Faidhi Hasif Ahmad Roshidi and Muhammad Nur Hakim Hariri. (2018) [Student Project] (Unpublished)

Portable sieve for greensand and cast Damascus steel knife / Wan Muhammad Adli Mustaqim Wan Ibrahim. (2022) [Student Project] (Submitted)

The influence of geometry specimens on mild steel in slow cooling process / Muhammad Amar Zulhaikal Zamre. (2022) [Student Project] (Submitted)

An experimental investigation of uncoated WC-Co tool life and wear in turning of stainless steel / Nur Affatin Zawawi. (2016) [Student Project] (Unpublished)