Items where Subject is "Machine tools and machining"

A

A study of the effects of machining parameters on the surface roughness in the turning process / Nor Akram Abdullah. (2010) Degree thesis, thesis, Universiti Teknologi MARA (UiTM).

Laboratory manual for Plant Engineering / Muhamad Faiz Abu Zaki and Mohd Alijufri Bastani. (2005) [Student Project] (Unpublished)

Study of hardness properties of butt welded joints using Metal Inert Gas (MIG) welding on mild steel plate / Muhammad Syahir Azman. (2022) [Student Project] (Unpublished)

Influence of carbon addition on sintering behaviour in ultrafine wc-co Powder / Aidilrizam Azmi. (2017) [Student Project] (Unpublished)

Optimization of wire cut EDM process parameters using response surface methodology (RSM) / Muhamad Razwan Abdul Aziz. (2017) [Student Project] (Unpublished)

Performance analysis of thermal arc spray aluminium coating as a sacrificial anode / Muhamad Hafiz Abd Malek. (2015) Masters thesis, thesis, Universiti Teknologi MARA.

Characterisation of Stress Intensity Factor with Magnetic Flux Signal Leakage in Stable Fatigue Crack Growth Region S. R. Ahmad ...[et al.]. (2018) Journal of Mechanical Engineering (JMechE), SI 5 (3). pp. 141-155. ISSN 18235514

PVACLAMP: Portable Vacuum Clamping for Tool Room / Norfariza Ab Wahab … [et al.]. (2017) In: Melaka International Intellectual Exposition (MIIEX 2017). Division of Research and Industry Linkages, Alor Gajah, Melaka.

B

Development of graphical user interface for milling machine energy prediction tool / Muhammad Ikmal Hakim Badrulsham. (2020) [Student Project]

C

Study on machining tungsten carbide with electrical discharge machining (EDM) using Taguchi method / Mohd Rahimatul Azwa Che Rahim. (2009) Degree thesis, thesis, Uinversiti Teknologi MARA (UiTM).

F

The effect of machining parameters on surface integrity of aluminium material using lathe machine / Fakhrul Adam Fazilan. (2022) [Student Project] (Submitted)

H

Comparative cost between manual and mechanize of harvesting technique in oil palm plantation / Muhammad Syahmi Haris Suhairi. (2015) [Student Project] (Unpublished)

The effect of machining parameters on surface integrity of mild steel material using lathe machine / Faiz Azzhar Hamzah. (2022) [Student Project] (Submitted)

Investigation of jolt squeeze machine specifications for dumbell design production and its characterizations / Muhammad Danish Haikal Hamzah. (2024) [Student Project] (Unpublished)

A novel combined-mode design for a MEMS-based micro passive direct methanol fuel cell / Umi Azmah Hasran ... [et al.]. (2024) Malaysian Journal of Chemical Engineering and Technology (MJCET), 7 (2): 1. pp. 49-61. ISSN 2682-8588

I

Effect of carbon addition and VC on mechanical properties in ultra-fine WC-Co cutting tool / Nurul Nazihah Ismail. (2017) [Student Project] (Unpublished)

Development of thermostable microencapsulated lactobacillus targeted gut delivery / Muhamad Fareez Ismail. (2018) In: The Doctoral Research Abstracts. IPSis Biannual Publication, 14 (14). Institute of Graduate Studies, UiTM, Shah Alam.

J

Design and innovation of chuck for lathe machine / Muhamad Faiz Jofri ... [et al.]. (2017) In: Melaka International Intellectual Exposition (MIIEX 2017). Division of Research and Industry Linkages, Alor Gajah, Melaka.

Effects of prosthesis stem length on stress distribution in cementless hip arthroplasty / Emmi Farisa Jaafar. (2009) Degree thesis, thesis, Universiti Teknologi MARA Shah Alam.

M

Automatic flour sifter / Alya Husna Mohd Shukry. (2022) [Student Project] (Unpublished)

Rotating Chicken Skewer / Khirwizam Md Hkhir and Nursharulhamir Johari. (2003) [Student Project] (Unpublished)

Process modelling and simulation for prediction of chip morphology during machining of stainless steel / Lafishahzreen Maharam. (2017) [Student Project] (Unpublished)

Steering Wheel Alignment JIG / Norakmal Maamor … [et al.]. (2012) In: RIID 2012: Innovation For Sustainable Growth. Bahagian Penyelidikan dan Jaringan Industri, UiTM Melaka, Alor Gajah, p. 35. (Unpublished)

Design of punch and die for trimming operation / Muhammad Asyraf Mohd Lizam. (2022) [Student Project] (Submitted)

Design and development of sling based on ping pong ball launcher / Muhammad Luq Ai Mohd Hassim. (2022) [Student Project] (Submitted)

The effect of machining parameters on surface integrity of aluminium material using vertical milling machine / Abdul Azim Mohd Zaidi. (2022) [Student Project] (Submitted)

Study of hardness on the mild steel in various cooling medium / Haziq Shazwan Mohd Ghazali. (2022) [Student Project] (Submitted)

Failure mode and effects analysis in manufacturing of milling process / Mohd Aslam Mohd Azaha. (2022) [Student Project] (Unpublished)

Design and fabrication of potato cutter machine / Muhammad Aidil Azzam Mat Nasir. (2022) [Student Project] (Submitted)

Mesin membanting padi / Zaibri Muhamad and Nik Mohd Nirman Mansor. (1995) [Student Project] (Unpublished)

Design and development of frictionless automotive transmission: power transmission analysis with virable speed motor / Din Iqbal Mahar Afandi. (2009) Degree thesis, thesis, Universiti Teknologi MARA Shah Alam.

Modeling bolt behavior using finite element analysis / Jumatirah Mohd Alias. (2006) [Student Project] (Unpublished)

Influence of carbon addition on mechanical properties in ultra-fine WC-Co cutting insert / Nur Atikah Muin. (2017) [Student Project] (Unpublished)

Design and analysis of mini extrusion machine for 3D printing filament / Ahmad Akmal Mustafa. (2020) [Student Project] (Unpublished)

Investigation on PETG tensile properties through 3D printing / Muhammad Syazrul Mohd Zahari. (2020) [Student Project] (Unpublished)

V-shaped bending support’ membantu dalam eksperimen ‘3-point bending test’ untuk tikus bersaiz kecil (V-shaped bending support helps in 3-point bending test experiment for small mice bone) / Noor Shafini Mohamad and Mohd Hafizi Mahmud. (2020) Jurnal Inovasi Malaysia (JURIM), 4 (1). pp. 1-14. ISSN 2600-7606

Upgrading of blending process for sand casting / Mohamad Hanafiah Mohamed Ali and Bushra Mokhtar. (2005) [Student Project] (Unpublished)

Pattern design for investment casting / Mohammad Naimie Mohamed Bakari and Rosniza Rabilah. (2005) [Student Project] (Unpublished)

N

Study of hardness properties of buttwelded joints using Shield Metal Arcwelding (SMAW) on stainless steel plate / Nik Mohamad Aqeel Nik Mohamad Kariman. (2022) [Student Project] (Submitted)

Influences of main machining process parameters and tool wear on the machining damage generated during edge milling CFRP composites / Nguyen Thi-Hue and Nguyen Dinh-Ngoc. (2023) Journal of Mechanical Engineering (JMechE), 20 (3): 18. pp. 355-370. ISSN 1823-5514 ; 2550-164X

Designing and fabricating a twin polishing machine / Nik Azizul Hisham Nik Abd Aziz and Nik Ahmad Sallehuddin Nik Mohammed. (1992) [Student Project] (Unpublished)

Three dimensional cutting force and tool deflection in micro-end milling AISI D2 / Noor Aniza Norrdin. (2016) Masters thesis, thesis, Universiti Teknologi MARA.

Graphical user interface for surface roughness prediction of CNC milling machine / Muhammad Qayyum Nor Asffan. (2020) [Student Project]

Fine Bone China Product using Ceramics Slip Rotary Moulding (CSRM) Technique / Norazne Nasir ...[et al.]. (2017) Journal of Mechanical Engineering (JMechE), SI 4 (4). pp. 31-42. ISSN 18235514

O

Bending and cutting links hand tools / Zamali Omar, Ayu Wirdawati Po'a and Siti Marlinna Chu Mohd Rizal Chu. (2012) In: RIID 2012: Innovation For Sustainable Growth. Bahagian Penyelidikan dan Jaringan Industri, UiTM Melaka, Alor Gajah, Melaka, p. 48.

Miniature drilling machine prototype / Muhammad Zakiruddin Osman @ Mohd Nordin. (2022) [Student Project] (Submitted)

R

Alat pengupas kelapa / Affandi Rumpa and Dayang Fatimah Abang Shebli. (1996) [Student Project] (Unpublished)

Smart grass cutter/ Muhammad Hifzhan Ruslan, Muhammad Ammar Maznan and Yusri Aizat Mohd Yasir Afkam. (2018) In: Electrical Engineering Innovation Competition & Exhibition (EEICE) 2018, 13-14 November 2018, Dewan Aspirasi, UiTM Cawangan Terengganu.

Dimensional accuracy of abs 3D printed part using 3D Espresso F220 machine / Ahmad Afiq Aiman Roslan. (2020) [Student Project]

S

Effect of cutting fluid pressure on machining of AISI 304 performances / Zainal Arifin Selamat and Mohd Razali Muhamad. (2008) In: Proceedings STSS 2008 Broadening Horizons Through Research Science and Technology, 3-4 June 2008, M.S. Garden Hotel, Kuantan Pahang.

Toolbox trolley / Muhammad Adam Shamsul Harisah, Faidhi Hasif Ahmad Roshidi and Muhammad Nur Hakim Hariri. (2018) [Student Project] (Unpublished)

Hydraulic axle shaft puller with stand / Muhammad Luqman Hakim Salyazid. (2022) [Student Project] (Unpublished)

A study of design new method cutting metal plate lead / Abdull Hadi Salleh. (2009) Degree thesis, thesis, Universiti Teknologi MARA Shah Alam.

An experimental investigation of TiCN tool life and tool wear in turning of titanium / Muhamad Anwar Salehudin. (2016) [Student Project] (Unpublished)

An experimental investigation of WC-Co tool life and tool wear in turning of titanium / Shamsiatun Shamsuddin. (2016) [Student Project] (Unpublished)

W

Portable sieve for greensand and cast Damascus steel knife / Wan Muhammad Adli Mustaqim Wan Ibrahim. (2022) [Student Project] (Submitted)

Z

The influence of geometry specimens on mild steel in slow cooling process / Muhammad Amar Zulhaikal Zamre. (2022) [Student Project] (Submitted)

An experimental investigation of uncoated WC-Co tool life and wear in turning of stainless steel / Nur Affatin Zawawi. (2016) [Student Project] (Unpublished)

Implementing loops system for controlling tool movement / Muhammad Faizul Rizal Zainal Alam. (2010) Degree thesis, thesis, Universiti Teknologi MARA.