Items where Subject is "Product testing"

A

Abd Jalil, Azizi (2001) Thermoplastic composite from aquilaria malacensis / Azizi Abd Jalil. [Student Project] (Unpublished)

Abdul Rahim, Mohd Ikmal Hisham (2020) Effect of layer thickness on repeatability of 3D printed PLA produced using 3D Espresso F220 / Mohd Ikmal Hisham Abdul Rahim. [Student Project] (Unpublished)

Azwan Zaini, Mohd Khairul (2011) Procedures for conducting usability evaluation experiment using eye tracker: a case study of Tobii T60 / Mohd Khairul Azwan Zaini. Degree Thesis , Universiti Teknologi MARA (UiTM) .

H

Husariman, Syahmie Arif Farhan (2022) Design and development of rocket based rubber hollow elastic ball launcher / Syahmie Arif Farhan Husariman. [Student Project] (Submitted)

I

Ishak, Mohd Asreen and Ahmad, Mohd Fauzi and Senik @ Abdul Mokhti, Mohamad Shihab (2003) Design of portable drawing board / Mohd Asreen Ishak, Mohd Fauzi Ahmad and Mohamad Shihab Senik @ Abdul Mokhti. [Student Project] (Unpublished)

J

Jafar, Amir Hamzi (2022) Design and fabrication of arbor clamper using 3d printer ender 800 / Amir Hamzi Jafar. [Student Project] (Submitted)

Jalil, Khairul Anwar and Ismail, Rahmat (1992) Kajian kemungkinan bagi menyediakan makmal ujian bahan / Khairul Anwar Jalil dan Rahmat Ismail. [Student Project] (Unpublished)

Jukepely, Mohamad Khairunnaim (2022) Design & fabricate 3D printer pencil case/box for student usage / Mohamad Khairunnaim Jukepely. [Student Project] (Submitted)

K

Kamarolzeman, Jawidah Adiba (2020) A study on the Personal Protective Equipment (PPE) used in occupational radiation protection / Jawidah Adiba Kamarolzeman. [Student Project] (Unpublished)

Khalmaiza, Muhammad Irfan (2022) Design and fabricate 3D handphone casing / Muhammad Irfan Khalmaiza. [Student Project] (Submitted)

L

Lahmuddin, Muhammad Azfar Ramdan (2022) Design and development of sling based tennis ball launcher / Muhammad Azfar Ramdan Lahmuddin. [Student Project] (Submitted)

M

Mazlan, Normann Syukran (2020) The design of heat extraction system for salinity gradient of solar pond / Normann Syukran Mazlan. [Student Project]

Mazuadi, Muhammad Arid Azwar (2022) Welding demontration table with adjuster / Muhammad Arid Azwar Mazuadi. [Student Project] (Submitted)

Mestor, Md. Khairul Fadli and Ismail, Khir Johari and Hasan, Mohd Fahmi (2005) The investment casting process of optimization / Md. Khairul Fadli Mestor, Khir Johari Ismail and Mohd Fahmi Hasan. [Student Project] (Unpublished)

Mohd Daud, Mohd Azuan and Yahya, Norhaida and Abdullah, Nor Shuhada (2007) Properties of particleboard using 16 years old petai belalang (Leucaena leucocephala) / Mohd Azuan Mohd Daud, Norhaida Yahya and Nor Shuhada Abdullah. [Student Project] (Unpublished)

Mohd Halid, Saiful Amirul Asyraf (2020) Balancing two wheeled using Arduino microcontroller / Saiful Amirul Asyraf Mohd Halid. [Student Project]

Mohd Hassim, Muhammad Luq Ai (2022) Design and development of sling based on ping pong ball launcher / Muhammad Luq Ai Mohd Hassim. [Student Project] (Submitted)

Mohd Hothzani, Mohamad Shahrul (2022) Design and fabrication of RC boat propeller using 3D printer / Mohamad Shahrul Mohd Hothzani. [Student Project] (Submitted)

Mohd Razali, Muhammad Faris (2022) Design and development of catapult based tennis ball launcher / Muhammad Faris Mohd Razali. [Student Project] (Submitted)

Mohd Saren, Muhamad Syakir Alif (2022) Design and fabrication of sliding platform component of SPD (Smart Parcel Dropbox) / Muhamad Syakir Alif Mohd Saren. [Student Project] (Submitted)

Mohd Sobri, Muhammad Izzuddin (2022) Design and development of sling based squash ball launcher / Muhammad Izzuddin Mohd Sobri. [Student Project] (Submitted)

Mohd Zahari, Muhammad Syazrul (2020) Investigation on PETG tensile properties through 3D printing / Muhammad Syazrul Mohd Zahari. [Student Project] (Unpublished)

N

Naji, Heally and Said @ Saat, Safizam (1999) Merekabentuk kaki sokongan untuk orang lumpuh / Heally Naji and Safizam Said @ Saat. [Student Project] (Unpublished)

Ngahadi, Nur Annisa (2020) Roughness prediction of fused deposition modelling / Nur Annisa Ngahadi. [Student Project]

Nordin, Ahmad Amirul (2017) Investigation of hardness gradient in carburizing of Fe-24Mn steel / Ahmad Amirul Nordin. [Student Project] (Unpublished)

O

Othman, Nor Amirah (2015) Properties of paper from cymbopogon nardus (serai wangi) by using different beating process/ Nor Amirah Othman. [Student Project] (Unpublished)

R

Rozy, Muhammad Firdaus (2022) Design and fabricate mini interceptor / Muhammad Firdaus Rozy. [Student Project] (Submitted)

S

Setapa @ Shari, Muhammad Danish Hariz (2022) Design and fabrication of antiseptic sprinkler component of Smart Parcel Dropbox (SPD) / Muhammad Danish Hariz Setapa @ Shari. [Student Project] (Submitted)

Z

Zamre, Muhammad Amar Zulhaikal (2022) The influence of geometry specimens on mild steel in slow cooling process / Muhammad Amar Zulhaikal Zamre. [Student Project] (Submitted)