Geopolymer mortars (GPM) are currently being explored as sustainable material alternatives to ordinary Portland cement-based mortars. However, GPM mix performance depends on the precursor, the alkaline-activated solution, the water content, and any additional materials. Graphene oxide (GO) is a promising nanomaterial with 3 major behaviors: it can act as a filler, a bridge, and a binder. However, the effectiveness of GO is highly dependent on its dosage and the availability of sufficient water for proper dispersion, as GO's hydrophilic nature tends to absorb water, reducing workability and altering the geopolymerization process, potentially leading to high porosity and weaker bond strength. The chemical composition, elements, and microstructure of the material influence both fresh and hardened properties of GPM. Hence, this study analyzed the physical and chemical characteristics of the raw materials, namely, fly ash class F (FA), ground granulated blast furnace slag (GGBS), and GO. The GPM formulation, incorporating different GGBS replacement levels in FA (0%, 20%, 40%, 60%, 80%, and 100%) and without GO, was investigated for flowability, compressive strength, setting time, and dry shrinkage. An optimum GPM formulation was chosen as the baseline mix based on its overall performance across the tested properties. Six different GO dosages (0 wt.%, 0.02 wt.%, 0.04 wt.%, 0.06 wt.%, 0.08 wt.% and 0.10 wt.%) with 3 different water-to-precursor ratio (w/p) (0.00, 0.10, and 0.20) were included in the baseline mix (GO0-GPM) to investigate its performance on flowability, setting time, compressive strength, dry shrinkage, water absorption, acid attack, and rapid chloride permeability. A total of 18 mix designs were analyzed in this phase, and 6 were selected as desired based on their combined fresh, hardened, and durability performance. The pore characteristics of the desired mixes were analysed, as was the bond behaviour. Bi-surface shear bond strength, slant shear bond strength, splitting tensile bond strength, and interfacial bond morphology (IBM) were analysed. Mohr’s Coulomb Principle was used to analyze the stress on the bond interface. The results showed that the performance of GPM was not controlled by GO dosage alone, but by the interaction between GO content and w/p ratio. The results further confirmed that incorporating 0.04-0.06 wt.% GO with w/p 0.10 enhanced the bonding performance of GPM by promoting a denser interfacial microstructure and improving shear resistance across the interface. Among the investigated mixes, the optimum range of 0.04-0.06 wt.% GO with w/p 0.10 produced the most balanced performance by improving matrix densification, pore refinement, durability resistance, and interfacial bond behaviour. The observation on microstructural characteristics aligns with the observed mechanical improvements and indicates that GO functions as a nano-reinforcement and nucleation agent, thereby promoting more efficient geopolymerisation. The synergistic effect of GO and water was analysed on fresh, hardened, and bond behaviour properties, and the findings provide a practical basis for optimising low-dosage GO-modified GPM where bond strength and durability are critical.
| Item Type: | Thesis (PhD) |
|---|---|
| Creators: | Creators Email / ID Num. Shamsol, A’lia Sofea UNSPECIFIED |
| Contributors: | Contribution Name Email / ID Num. Thesis advisor Mohd Apandi, Nazirah UNSPECIFIED Thesis advisor Yee, Hooi Min UNSPECIFIED Thesis advisor Abdullah, Mohd Mustafa Al Bakri UNSPECIFIED Thesis advisor Ahmad Zailani, Warid Wazien UNSPECIFIED |
| Subjects: | T Technology > TA Engineering. Civil engineering T Technology > TA Engineering. Civil engineering > Materials of engineering and construction > Nonmetallic materials |
| Divisions: | Universiti Teknologi MARA, Shah Alam > Faculty of Civil Engineering |
| Programme: | Doctor of Philosophy (Civil Engineering) |
| Keywords: | Geopolymer mortar, GPM, Graphene oxide, GO, Fly ash, Ground granulated blast furnace slag, GGBS, Interfacial bond strength, Microstructure, Durability |
| Date: | August 2026 |
| URI: | https://ir.uitm.edu.my/id/eprint/150141 |
150141.pdf

